10-09-2013
The default firewall rules won't block access to websites.
You haven't shown us your configuration, so how can we know what's wrong?
Post the contents of:
- /etc/sysconfig/network-scripts/ifcfg-eth0 (assuming eth0 is the correct interface)
- ifconfig eth0 (again assuming eth0 is the correct interface)
- /etc/resolv.conf
- /etc/sysconfig/network
Also, are you running "RHEL" on a physical server or in a VM?
10 More Discussions You Might Find Interesting
1. IP Networking
I have installed Solaris 8.0 and want to find out how can I go in and change my network setup and external IP setup. At the moment system running but I can not connect to the internet. But my lan card shows that I am on the network. I also get some advice that I should check the $Socks but how do I... (1 Reply)
Discussion started by: Cdrive
1 Replies
2. UNIX for Dummies Questions & Answers
Im on XP now but when im on linux how do I connect to the internet?
I don't think AOL works with it but are there any free programs that I can use with it? (8 Replies)
Discussion started by: NoPepsiForYou
8 Replies
3. UNIX for Dummies Questions & Answers
Hi all,
Is it possible (as I only have dial-up) to utilise my existing WinXP PC as a gateway to the internet for my 2nd PC (RH 8.0)?? .So connect with XP and have RH use a network connection (I guess) through the XP box and to the internet.
If so, could I please have some links thrown my... (1 Reply)
Discussion started by: Cameron
1 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them.
If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies
5. Linux
Hi,
I can ping www.yahoo.com (then domain name server is OK) but I can not navigate by Motzila to www.yahoo.com or any other Web Site.
What can be the problem ? Mozila is configured in preference /advance to go automaticaly on WEB.
We are under RED HAT AS3.
What should I check ?
Many thanks... (1 Reply)
Discussion started by: big123456
1 Replies
6. UNIX for Dummies Questions & Answers
I have just installed Linux and everything looks great, but how do I get my browser (Mozilla) to connect to my internet service provider?
I have a cable connection to Bigpond in Australia, if that means anything - the ISP will not provide support for Linux.
Your help would be greatly... (2 Replies)
Discussion started by: openhead
2 Replies
7. IP Networking
Hello all
this is general question , if i have web server installed in my local pc and i have client that connecting to that web server
can i force it always to go via the internet network ?
the reason im asking is .. that im noticed when i close my internet connection i still can connect to my... (2 Replies)
Discussion started by: umen
2 Replies
8. Solaris
hi there, hope your chakras are all doing well :-)
just installed solaris 10 on my laptop, all seems fine except the internet. How can i connect on a DSL line?. spent 7 days and 3 nights trying but couldnt find the starting point....
alikun (22 Replies)
Discussion started by: alikun
22 Replies
9. UNIX for Dummies Questions & Answers
I am trying to connect a Solaris 10 PC to the internet via a Linksys router and a cable modem. I have tried following suggestions in one of the posts here for manual setup but so far no luck.
Does the Solaris 10 install for x86 automatically pick up the internet connection?
Dave :>) (4 Replies)
Discussion started by: dohling
4 Replies
10. SCO
Hi, I have a router, 192.168.1.1, and an internet router, 10.0.0.138. I have connected the server to the 1st router and assigned it a IP address of 192.168.1.1. I can ping both routers successfully but I have no access to internet. Any suggestions? sco5.0.7 (11 Replies)
Discussion started by: juan.navarrete
11 Replies
LEARN ABOUT ULTRIX
ntp.conf
ntp.conf(5) File Formats Manual ntp.conf(5)
Name
ntp.conf - Network Time Protocol configuration file
Description
The file is the configuration file for the Network Time Protocol (NTP) daemon, This file must be configured on your system before running
Any host names that you specify in the file must have an entry in the file, or an entry in the master database, if the database is being
served to your system by BIND/Hesiod or Yellow Pages.
The file has four entry formats:
trusting no
This entry guarantees that your system synchronizes only to the NTP servers identified in the peer and server entries specified. Dig-
ital recommends that all systems include the entry.
peer server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system may also provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP servers should be configured with entries.
server server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system can not provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP clients should be configured with entries.
peer /dev/null LOCL 1 -5 local
This entry identifies your system as a local reference clock. A local reference clock is the most accurate system clock available at
your site. If you receive time synchronization from the Internet NTP service, you should not include this entry on any of your sys-
tems. At most, one system in a set of nodes running should be identified as a local reference clock.
A host which specifies this entry should not specify any or entries.
Examples
This is a sample configuration file for an NTP client which receives time synchronization from the NTP servers: and Lines beginning with a
number sign (#) are comments.
#
# NTP Configuration File
# This file is mandatory for the ntpd daemon
#
#
#
# ** A L L **
#
# "trusting no" prevents this host from synchronizing
# to any host that is not listed below. It is recommended
# that all hosts include the line "trusting no".
#
trusting no
#
#
# ** S E R V E R **
#
# If you are configuring a server, use "peer" entries to
# synchronize to other NTP servers. For example, server1,
# server2, and server3.
#
#peer server1
#peer server2
#peer server3
#
#
#
#
# ** C L I E N T **
#
# If you are configuring a client, use "server" entries to
# synchronize to NTP servers. For example, server1, server2,
# and server3.
#
server server1
server server2
server server3
#
#
#
# ** L O C A L R E F E R E N C E C L O C K **
#
# If you are configuring a local reference clock, include the
# following entry and the "trusting no" entry ONLY.
#
#peer /dev/null LOCL 1 -5 local
#
See Also
ntp(1), ntpd(8), ntpdc(8)
RFC 1129--Internet time synchronization: The Network Time Protocol
Introduction to Networking and Distributed System Services
ntp.conf(5)