10-07-2013
Regarding connecting to internet from RHEL 5 server
Dear All,
I have a RHEL 5 server of 64 bit . I have disabled the firewalls and added the name server also in resolv.conf.
I want to connect to internet inorder to link the machine with Linux Network.
# I could not connect to any website from this server for ex
ping google.com is not working .
So I need to configure internet in this server...Pl give me some ideas on this.....
10 More Discussions You Might Find Interesting
1. IP Networking
I have installed Solaris 8.0 and want to find out how can I go in and change my network setup and external IP setup. At the moment system running but I can not connect to the internet. But my lan card shows that I am on the network. I also get some advice that I should check the $Socks but how do I... (1 Reply)
Discussion started by: Cdrive
1 Replies
2. UNIX for Dummies Questions & Answers
Im on XP now but when im on linux how do I connect to the internet?
I don't think AOL works with it but are there any free programs that I can use with it? (8 Replies)
Discussion started by: NoPepsiForYou
8 Replies
3. UNIX for Dummies Questions & Answers
Hi all,
Is it possible (as I only have dial-up) to utilise my existing WinXP PC as a gateway to the internet for my 2nd PC (RH 8.0)?? .So connect with XP and have RH use a network connection (I guess) through the XP box and to the internet.
If so, could I please have some links thrown my... (1 Reply)
Discussion started by: Cameron
1 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them.
If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies
5. Linux
Hi,
I can ping www.yahoo.com (then domain name server is OK) but I can not navigate by Motzila to www.yahoo.com or any other Web Site.
What can be the problem ? Mozila is configured in preference /advance to go automaticaly on WEB.
We are under RED HAT AS3.
What should I check ?
Many thanks... (1 Reply)
Discussion started by: big123456
1 Replies
6. UNIX for Dummies Questions & Answers
I have just installed Linux and everything looks great, but how do I get my browser (Mozilla) to connect to my internet service provider?
I have a cable connection to Bigpond in Australia, if that means anything - the ISP will not provide support for Linux.
Your help would be greatly... (2 Replies)
Discussion started by: openhead
2 Replies
7. IP Networking
Hello all
this is general question , if i have web server installed in my local pc and i have client that connecting to that web server
can i force it always to go via the internet network ?
the reason im asking is .. that im noticed when i close my internet connection i still can connect to my... (2 Replies)
Discussion started by: umen
2 Replies
8. Solaris
hi there, hope your chakras are all doing well :-)
just installed solaris 10 on my laptop, all seems fine except the internet. How can i connect on a DSL line?. spent 7 days and 3 nights trying but couldnt find the starting point....
alikun (22 Replies)
Discussion started by: alikun
22 Replies
9. UNIX for Dummies Questions & Answers
I am trying to connect a Solaris 10 PC to the internet via a Linksys router and a cable modem. I have tried following suggestions in one of the posts here for manual setup but so far no luck.
Does the Solaris 10 install for x86 automatically pick up the internet connection?
Dave :>) (4 Replies)
Discussion started by: dohling
4 Replies
10. SCO
Hi, I have a router, 192.168.1.1, and an internet router, 10.0.0.138. I have connected the server to the 1st router and assigned it a IP address of 192.168.1.1. I can ping both routers successfully but I have no access to internet. Any suggestions? sco5.0.7 (11 Replies)
Discussion started by: juan.navarrete
11 Replies
LEARN ABOUT OPENSOLARIS
auscope
AUSCOPE(1) General Commands Manual AUSCOPE(1)
NAME
auscope - Network Audio System Protocol Filter
SYNOPSIS
auscope [ option ] ...
DESCRIPTION
auscope is an audio protocol filter that can be used to view the network packets being sent between an audio application and an audio
server.
auscope is written in Perl, so you must have Perl installed on your machine in order to run auscope. If your Perl executable is not
installed as /usr/local/bin/perl, you should modify the first line of the auscope script to reflect the Perl executable's location. Or,
you can invoke auscope as
perl auscope [ option ] ...
assuming the Perl executable is in your path.
To operate, auscope must know the port on which it should listen for audio clients, the name of the desktop machine on which the audio
server is running and the port to use to connect to the audio server. Both the output port (server) and input port (client) are automati-
cally biased by 8000. The output port defaults to 0 and the input port defaults to 1.
ARGUMENTS
-i<input-port>
Specify the port that auscope will use to take requests from clients.
-o<output-port>
Determines the port that auscope will use to connect to the audio server.
-h<audio server name>
Determines the desktop machine name that auscope will use to find the audio server.
-v<print-level>
Determines the level of printing which auscope will provide. The print-level can be 0 or 1. The larger numbers provide greater
output detail.
EXAMPLES
In the following example, mcxterm is the name of the desktop machine running the audio server, which is connected to the TCP/IP network
host tcphost. auscope uses the desktop machine with the -h command line option, will listen for client requests on port 8001 and connect
to the audio server on port 8000.
Ports (file descriptors) on the network host are used to read and write the audio protocol. The audio client auplay will connect to the
audio server via the TCP/IP network host tcphost and port 8001:
auscope -i1 -o0 -hmcxterm
auplay -audio tcp/tcphost:8001 dial.snd
In the following example, the auscope verbosity is increased to 1, and the audio client autool will connect to the audio server via the
network host tcphost, while displaying its graphical interface on another server labmcx:
auscope -i1 -o0 -hmcxterm -v1
autool -audio tcp/tcphost:8001 -display labmcx:0.0
SEE ALSO
nas(1), perl(1)
COPYRIGHT
Copyright 1994 Network Computing Devices, Inc.
AUTHOR
Greg Renda, Network Computing Devices, Inc.
1.9.3 AUSCOPE(1)