Hi folks,
The server time is no tgetiing synched up with the NTP server.
I tried ntpdate -u <ipadress> this is not working. please help out.
regards,
Sag. (7 Replies)
Ok, I have 4 production systems. There is one NTP server for all four systems. In each system there is one Solaris 10 box that points to that NTP server. All of the other machines in the system point to the Solaris 10 machine to get their time sync.
All four Solaris 10 machines have essentially... (2 Replies)
Hi,
My Linux VMs are running on citrix XEN.Somehow the time drift is too high (going very fast). Even if the correct time configured using date -s command, for every 1 hr it is differing almost 5 - 10 mins.
Tried configuring ntpd (local NTP server) and still it is not synchronized.
Machine... (2 Replies)
Hi folks, I have developed a Linux server for my customer. After migrating the server to my customer site, I was trying to sync its time to the NTP time servers at my customer site.
Below is the ntp.conf:
% vi /etc/ntp.conf
# Permit time synchronization with our time source, but do not
# permit... (2 Replies)
Hi All,
I deployed the rhel7 server in the bare metal hardware. I want to configure the rhel7 server to sync time with bios. I tired the below commands. Still it did not sync the time with bios.
Thanks,
Kalai (3 Replies)
Hi
I have a requirement to rsync from remote to local machine via ssh and sync files that are changed in last n hours.
pgrep to check if no other sync is running
pgrep -f rsync.*/opt > /dev/null || rsync --bwlimit=10000 -avz --delete root@X.X.X.X:/var/source/ /opt/dest/ >> /home/log 2>&1... (0 Replies)
Hello,
We have Windows 10 machine connected to Sparc T5440 server via serial cable.
We access the server from the Windows 10 machine using putty via serial connection. This allows us to access ILOM and Unix.
We have recently noticed that whenever we reboot the windows machine (Windows 10),... (11 Replies)
Discussion started by: jasonu
11 Replies
LEARN ABOUT SUSE
ntptrace
ntptrace(1) General Commands Manual ntptrace(1)NAME
ntptrace - trace a chain of NTP servers back to the primary source
SYNOPSIS
ntptrace [ -vdn ] [ -r retries ] [ -t timeout ] [ server ]
DESCRIPTION
ntptrace determines where a given Network Time Protocol (NTP) server gets its time from, and follows the chain of NTP servers back to
their master time source. If given no arguments, it starts with localhost . Here is an example of the output from ntptrace :
% ntptrace localhost: stratum 4, offset 0.0019529, synch distance 0.144135 server2ozo.com: stratum 2, offset 0.0124263, synch distance
0.115784 usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993, refid On each line, the fields are (left to right): the host
name, the host stratum, the time offset between that host and the local host (as measured by ntptrace ; this is why it is not always zero
for " localhost "), the host synchronization distance, and (only for stratum-1 servers) the reference clock ID. All times are given in sec-
onds. Note that the stratum is the server hop count to the primary source, while the synchronization distance is the estimated error rela-
tive to the primary source. These terms are precisely defined in RFC-1305.
OPTIONS -d Turns on some debugging output.
-n Turns off the printing of host names; instead, host IP addresses are given. This may be useful if a nameserver is down.
-r retries Sets the number of retransmission attempts for each host (default = 5).
-t timeout Sets the retransmission timeout (in seconds) (default = 2).
-v Prints verbose information about the NTP servers.
BUGS
This program makes no attempt to improve accuracy by doing multiple samples.
SEE ALSO
More documentation is available in the package ntp-doc.
AUTHOR
David L. Mills <mills@udel.edu>
ntp 4.1.1b-r5ntptrace(1)