Sponsored Content
Special Forums IP Networking Route packets over specified interface Post 302859293 by Corona688 on Wednesday 2nd of October 2013 05:38:39 PM
Old 10-02-2013
For starters, whether IP ranges are "open" has little to do with whether your computer actually uses them.

You need to set up rules in your routing table, not your firewall, that things going to IP's related to spotify should go to gateway x via interface y. This rule has to come before your catchall rule.
 

9 More Discussions You Might Find Interesting

1. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

2. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

3. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. IP Networking

How to route all incoming packets from one virtual interface?

Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1. eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72 inet addr:192.168.10.15 eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies

8. IP Networking

How to route packets back to incoming interface?

Hi folks, I have a debian server running an Apache daemon on the eth0 interface. Now from time to time the server has to open an openvpn connection (tun0) to other networks to get some data from there. During this period the Apache is no longer reachable under it's IP address on eth0 because all... (6 Replies)
Discussion started by: flyingwalrus
6 Replies

9. IP Networking

Packet going out of wrong interface due to OS automatically added cache route with lower metric

RHEL 7.0, IPV6 Scenario: I have routed specific network using network scripts. 1. "ip -6 route show" shows that route has been added. ( with metric 1024) 2. Ping of the specific IP through that route is successful. 3. Now after few days, for some reason, we see that cache route appears for... (3 Replies)
Discussion started by: msr1981
3 Replies
APF(1)							      General Commands Manual							    APF(1)

NAME
apf - easy iptables based firewall system SYNOPSIS
apf DESCRIPTION
This manual page documents briefly the apf command. This manual page was written for the Debian distribution because the original program does not have a manual page. Advanced Policy Firewall (APF) is an iptables (netfilter) based firewall system designed around the essential needs of today's Internet deployed servers and the unique needs of custom deployed Linux installations. The configuration of APF is designed to be very informative and present the user with an easy to follow process, from top to bottom of the configuration file. The management of APF on a day-to-day basis is conducted from the command line with the 'apf' command, which includes detailed usage information and all the features one would expect from a current and forward thinking firewall solution. OPTIONS
apf follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -s|--start load all firewall rules -r|--restart stop (flush) & reload firewall rules -l|--list list all firewall rules -t|--status output firewall status log -e|--refresh refresh & resolve dns names in trust rules -a <HOST CMT|--allow <HOST COMMENT> add host (IP/FQDN) to allow_hosts.rules and immediately load new rule into firewall -d <HOST CMT|--deny <HOST COMMENT> add host (IP/FQDN) to deny_hosts.rules and immediately load new rule into firewall -u <HOST>|--remove <HOST> remove host from [glob]*_hosts.rules and immediately remove rule from firewall -o|--ovars output all configuration options COPYRIGHT
Copyright (C) 1999-2007, R-fx Networks <proj@r-fx.org> Copyright (C) 2007, Ryan MacDonald <ryan@r-fx.org> This program may be freely redistributed under the terms of the GNU GPL This manual page was written by Giuseppe Iuculano <giuseppe@iuculano.it>, for the Debian project (but may be used by others). August 17, 2008 APF(1)
All times are GMT -4. The time now is 04:28 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy