Hi
I have my DNS servers (BIND 8) running on two Solaris 8 boxes. I need to be able to resolve an address blah.xxx.net to an IP address followed by :8080 - (for Tomcat). I tried doing this in my zone file but it failed. Can someone give me a pointer on where this configuration should be done?... (1 Reply)
hey everyone,
i have just finished configuring apache 2.0 with the php and pgsql modules installed on it.. httpd.conf is configured and everything is running right after a lengthy bit of reading and struggling with the system.. the only problem left is how do i enable the port that i would access... (3 Replies)
Hi. I ran nmap on my server, and I get the following:
Starting Nmap 4.76 ( http://nmap.org ) at 2009-03-19 16:33 EDT
Interesting ports on -------- (-----):
Not shown: 997 closed ports
PORT STATE SERVICE
22/tcp open ssh
80/tcp open http
6881/tcp open bittorrent-tracker
The... (0 Replies)
Hi All,
I am installing Infosphere (ETL tool) on solaris 10.
One of the requirement is to open multiple ports for different apps that will be installed. I ran netstat -n | grep 9080 (,etc) but that did not return anything.
I have attached the requirement. Can anyone guide me about how to... (3 Replies)
i want to kill a tcp connection by killing its pid
with netstat -an i got the tcp ip connection on port 5914
but when i type ps -a or ps-e there is not such process running on port 5914
is it possible that because i do not log on with proper user account i can not see that process running? (30 Replies)
I installed linux on one of my system and assigned valid network ip to it.
I am able to connect to net properly.
But when I try to putty this system from another system using ssh at port 22 then it gives me connection timed out error.
When I ping the system it responds fine but still unable to... (2 Replies)
Dear Experts,
I am trying to open 8080 port on my Aix 7.1 server. I made an entry in /etc/services for the port. and refreshed the inetd service. But when I try to telnet localhost 8080, telnet is not happening. connection refused error is coming.
I can able to telnet localhost 23 its working... (9 Replies)
Below is what i did to open the firewall port on
# sudo firewall-cmd --zone=public --add-port=27012/tcp --permanent
Warning: ALREADY_ENABLED: 27012:tcp
success
# sudo firewall-cmd --reload
success
# firewall-cmd --list-all
public
target: default
icmp-block-inversion: no
... (10 Replies)
Discussion started by: mohtashims
10 Replies
LEARN ABOUT SUNOS
ssh-http-proxy-connect
ssh-http-proxy-connect(1) User Commands ssh-http-proxy-connect(1)NAME
ssh-http-proxy-connect - Secure Shell proxy for HTTP
SYNOPSIS
/usr/lib/ssh/ssh-http-proxy-connect [-h http_proxy_host] [-p http_proxy_port] connect_host connect_port
DESCRIPTION
A proxy command for ssh(1) that uses HTTP CONNECT. Typical use is where connections external to a network are only allowed via a proxy web
server.
OPTIONS
The following options are supported:
-h http_proxy_host Specifies the proxy web server through which to connect. Overrides the HTTPPROXY and http_proxy environment vari-
ables if they are set.
-p http_proxy_port Specifies the port on which the proxy web server runs. If not specified, port 80 is assumed. Overrides the HTTP-
PROXYPORT and http_proxy environment variables if they are set.
OPERANDS
The following operands are supported:
http_proxy_host The host name or IP address (IPv4 or IPv6) of the proxy.
http_proxy_port The numeric port number to connect to on http_proxy_host.
connect_host The name of the remote host to which the proxy web server is to connect you.
connect_port The numeric port number of the proxy web server to connect you to on http_proxy_host.
EXAMPLES
The recommended way to use a proxy connection command is to configure the ProxyCommand in ssh_config(4) (see Example 1 and Example 2).
Example 3 shows how the proxy command can be specified on the command line when running ssh(1).
Example 1: Setting the proxy from the environment
The following example uses ssh-http-proxy-connect in ssh_config(4) when the proxy is set from the environment:
Host playtime.foo.com
ProxyCommand /usr/lib/ssh/ssh-http-proxy-connect
playtime.foo.com 22
Example 2: Overriding proxy environment variables
The following example uses ssh-http-proxy-connect in ssh_config(4) to override (or if not set) proxy environment variables:
Host playtime.foo.com
ProxyCommand /usr/lib/ssh/ssh-http-proxy-connect -h webcache
-p 8080 playtime.foo.com 22
Example 3: Using the command line
The following example uses ssh-http-proxy-connect from the ssh(1) command line:
example$ ssh -o'ProxyCommand="/usr/lib/ssh/ssh-http-proxy-connect
-h webcache -p 8080 playtime.foo.com 22"' playtime.foo.com
ENVIRONMENT VARIABLES
HTTPPROXY Takes the http_proxy_host operand to specify the default proxy host. Overrides http_proxy if both are set.
HTTPPROXYPORT Takes the http_proxy_port operand to specify the default proxy port. Ignored if HTTPPROXY is not set.
http_proxy URL format for specifying proxy host and port.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsshu |
+-----------------------------+-----------------------------+
|Interface Stability |Stable |
+-----------------------------+-----------------------------+
SEE ALSO ssh(1), ssh-socks5-proxy-connect(1), ssh_config(4), attributes(5)SunOS 5.10 24 Oct 2001 ssh-http-proxy-connect(1)