Could USB ever take over PCI Post: 302843685

9 More Discussions You Might Find Interesting

1. BSD

WLAN PCI Cards

Hi! I just wanted to know what network cards are supported in FreeBSD. I have looked at the list of supported cards but I can't find any of them in the stores. Is the list not updated, I would really preciate info about where (in EU, Sweden) I can buy them. /Peter

2. Solaris

Pci Id

How do I get the PCI ID for my Realtek adapter? It's a Solaris x86 installation.

3. UNIX for Dummies Questions & Answers

bad pci slot?

Hi, im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the...

4. UNIX for Dummies Questions & Answers

sun blade 100 test-all frozen at pci@1f,0/usb/c,3

platform: sunblade 100 Solaris 10. When running a test-all from the ok prompt on this new (to me) system, it locks up at pci@1f,0/usb/c,3. It's been there for about 25 minutes. I do have a usb keyboard and mouse attached, both are known good. There is no flash stick/ thumb drive...

5. Linux

PCI Card recognized

I installed PCI Card HP SC44Ge - SAS1068E on my linux CentOS 5.4 is there a way to find out if the PCI is properly installed and recognized by linux. lspci is enough? just to add that PCI card is connected to a tape... also how can I find out driver and firmware version? thanks a...

6. UNIX for Dummies Questions & Answers

USB-USB cable between linux and windows computers

Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive. Thanks!

7. Programming

help writing pci firmware

For a project that I'm working on I want to write a low level PCI driver, but I can't seem to find any free/cheap documentation on PCI firmware specifications. I came across the "pci firmware specification 3.0" manual but this costs USD $1000 :eek:. I am not developing a commercial product...

8. Solaris

available PCI slots on v440

How do I find any available PCI slots on a v440? When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used. ================================= IO Devices ================================= Bus Freq Brd Type MHz Slot ...

9. Slackware

converting mouse to pci

Need to free up a usb port for webcam. What does xorg.conf look like in order to work if I move mouse to PCI port via a converter plug?

LEARN ABOUT FREEBSD

usb_template

USB_TEMPLATE(4) 					   BSD Kernel Interfaces Manual 					   USB_TEMPLATE(4)

NAME

     usb_template -- USB templates

SYNOPSIS

     To compile this module into the kernel, place the following line in your kernel configuration file:

	   device usb_template

     To load the module at boot time, place the following line in loader.conf(5):

	   usb_template_load="YES"

DESCRIPTION

     The usb_template module implements various USB templates that are needed when programming an USB device side driver.  A USB template consists
     of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
     descriptors, USB strings and additional USB descriptors.  The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
     ernet and Message Transfer Protocol.  USB templates are currently selected using the "hw.usb.template" sysctl.  The "hw.usb.template" value
     can be changed at any time, but will not have any effect until the USB device has been re-enumerated.

SEE ALSO

     usb(4)

STANDARDS

     The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.

HISTORY

     The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.

BSD
								  March 18, 2014							       BSD