08-07-2013
smazshah,
- What is the model of your server. and OS version.
$ model ; uname -a
-How you have connected the disk, are they connected in the front bay or are this SAN disks.
In first output it shows CLAIMED, c10t5d0 c10t4d0 that is good, however if the disks are not in CLAIMED state you can not use them for the task.
- After you have presented the disks, make sure you have executed :
# ioscan ; ioscan -fnC disk
# insf -e -C disk
- Then check their condition:
# ioscan -fnH 0/4/1/0.0.0.4.0 ; ioscan -fnH 0/4/1/0.0.0.5.0
# diskinfo /dev/rdsk/c10t5d0 ; diskinfo /dev/rdsk/c10t4d0
- Once above looks good , you can go ahead with RAID-1 mirroring.
This is software mirror, you should have "MirrorDisk/UX " bundle installed with license.
if you have MCOE os , then it ll be bundled with the OS.
To check what type of OE you have you can use # swlist -l bundle | grep -i HPUX11
- If MirrorDisk/UX is ok, you can go ahead and do the mirroring of the disk RAID1.
Few steps outlined for having RAID1 filesystems on the two disk:
1. pvcreate both the disks. # pvcreate -f /dev/rdsk/c10t4d0
2. Create a volume group say vg01 , add the 2nd disk also. with vgcreate , vgextend
3. Create a Filesystem, that you want redundant. (RAID 1 ). with lvcreate and newfs
4. Proceed with mirror: Use lvextend -m 1 <lv_path> <2nd_disk>
5. check with lvdisplay -v <lv_name> , you will see 2 PE. in the LV. That means it is mirrored.
6. If one disk fails, your filesystem & its data, that was created per step 3, will be intact.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hello,
I am having a Problem with an Arena EX3 Raid on an HPUX 10.20 Workstation.
Everything is working fine until I shutdown the Server and power off the Raid. Then I get a filesystem corruption on the Raid. This happens everytime.
The Raid is configured as Raid Level 1.
I would really... (1 Reply)
Discussion started by: nleuenbe
1 Replies
2. Shell Programming and Scripting
I am running HPUX and using WLM (workload manager). I want to write a script to fork CPUs to basically take CPUs from other servers to show that the communication is working and CPU licensing is working. Basically, I want to build a script that will use up CPU on a server. Any ideas? (2 Replies)
Discussion started by: cpolikowsky
2 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. HP-UX
I'm sharing this in case anybody needs it. Modified from the original solaris pwage script. This modified hpux script will check /etc/password file on hpux trusted systems search /tcb and grep the required u_succhg field. Calculate days to expiry and notify users via email.
original solaris... (2 Replies)
Discussion started by: sparcguy
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT OSF1
volmirror
volmirror(8) System Manager's Manual volmirror(8)
NAME
volmirror - Mirrors volumes on a disk or control default mirroring
SYNOPSIS
/usr/sbin/volmirror [-g diskgroup] [-d yes|no] medianame [new_medianame...]
/usr/sbin/volmirror [-g diskgroup] [-d yes|no] -a [new_medianame...]
/usr/sbin/volmirror [-g diskgroup] [-d yes|no]
/usr/sbin/volmirror [-g diskgroup] -D
OPTIONS
The volmirror command supports the following options: Limits operation of the command to the given disk group, as specified by disk group
ID or disk group name. The medianame operands will be evaluated relative to the given disk group. If no disk group is supplied to the
volmirror command, rootdg is presumed. Changes the default for subsequent volume creation, depending on the option argument. If the option
argument is yes, all subsequent volumes created using the volassist command will automatically be created as mirrored volumes. If the
option argument supplied is no, mirroring will be turned off for future volumes by default. Displays current default status for mirroring.
Mirrors all existing volumes for the specified disk group.
DESCRIPTION
The volmirror command provides a mechanism to mirror all the contents of a specified disk, to mirror all currently unmirrored volumes in
the specified disk group, or to change or display the current defaults for mirroring. All volumes that have only a single plex (mirror
copy), will be mirrored by adding an additional plex.
Volumes containing subdisks that reside on more than one disk will not be mirrored by volmirror.
The volmirror command is generally called from the voldiskadm menus. It is not an interactive command and once called, will continue until
completion of the operation or until a failure is detected.
Note
Due to the nature of generating mirror copies of volumes, this command may take a considerable time to complete.
In the first listed form of the command, the disk media name is supplied on the command line to volmirror. That name is taken to be the
only disk from which volumes should be mirrored. In the case of mirroring volumes from a specified disk, only simple single-subdisk volumes
are mirrored.
In the first and second listed forms of the command, the new_medianame ... parameter identifies a new disk media name (or set of names).
The mirroring operation being performed will use these names as targets on which to allocate the mirrors. An error will result if the same
disk is specified for both the source and target disk and if no other viable targets are supplied.
EXAMPLES
The following are examples of the use of the volmirror command. The following command mirrors the contents of the disk named disk01 to any
available space on any available disk. Subsequent calls to volassist will cause created volumes to be mirrored by default. volmirror -d
yes disk01 The following command displays the current status of default mirroring. It prints the string yes if mirroring is currently
enabled or no, if not. volmirror -D The following command mirrors any volumes on disk02 onto disk03. volmirror disk02 disk03
FILES
The defaults file for volassist parameters.
SEE ALSO
volintro(8), volassist(8), volrootmir(8)
volmirror(8)