10-19-2002
thanks but in the bios i have to boot of hd2 and then secondary boot is hd1 becasue if i boot of hd1 first all i get is 01010101 and that continues forevery like its trying to say something.
any other ideas ??????
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
we have a problem with a server UNIX SUN OS 5.7 :
we tried to reboot it and we have the following error message :
"boot load failed
the file just loaded does not appear to be executable "
we booted the server in single user mode with the cdrom
we made the mirrored disk bootable
we tried... (2 Replies)
Discussion started by: farzolito
2 Replies
2. Red Hat
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Discussion started by: hassan2
7 Replies
3. UNIX for Advanced & Expert Users
Hi All.
Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says
' Module dependencies up to date (no new kernel modules found).'
At this point it hangs and goes no further! Does this sound familiar to anyone?
I am running... (2 Replies)
Discussion started by: silvaman
2 Replies
4. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
5. UNIX for Dummies Questions & Answers
Hi
i have both Linux and Windows XP on my PC.
i used to use grub as a boot loader and everything was perfect, until
i reinstalled Windows.
apparently, Windows installer installed its own bootloader, that
doesn't recognize Linux.
i tried using a tool called GrubInstaller for Windows, and now... (4 Replies)
Discussion started by: shx2
4 Replies
6. Solaris
Hi everyone,
I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies
7. UNIX for Dummies Questions & Answers
I'm trying to install Fedora 9 on a Dell OptiPlex GX300 machine. The instalation runs properly, but when the computer restarts after the instalation, it simply won't boot, like there's no OS installed.
I tried diffrent Linux distributions, but nothing works.
This are the partitions, maybe it's... (12 Replies)
Discussion started by: teis
12 Replies
8. UNIX for Dummies Questions & Answers
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
9. Solaris
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (12 Replies)
Discussion started by: bahjatm
12 Replies
10. Solaris
Hi all,
I have the the following SCSI diagnostic codes shown in the attached photo
I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
LEARN ABOUT FREEBSD
boot.config
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)
NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO
boot(8), loader(8)
AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD
May 13, 2007 BSD