Hey all,
I am haivng n number of files all of them are of the same format but different details. i.e
File1 is having the folloeing details:
"Account1",123
"Account2",10
"Account3",12355
"Accountn",555
File2 is having the folloeing details:
"Account1",1234
"Account2",100... (5 Replies)
This is my script. I am pulling the status of some hard where, but the status is in numerical form. The number 4 means Major and the 5 means Critical. In my script I would like to show the alarm type in aplha rather than numeric form. So if instead of seeing a 4 or 5 you would see MAjor or... (11 Replies)
I need help in what to do with a bash script? I'm trying to run a command to output the data from a table and then insert it into commands. Looping for each row of data.
For example the output data from a table:
10 John house
20 Jane apt
30 Joe townhomeThen I need to take the output... (1 Reply)
Hello all
siteexplorer.search.yahoo.com can output results in tsv format, when opened in excel I get 4 columns.
I would like to wget that file, which I can do. I would then like to pull the 2nd column and output it only.
I've searched around and found a few bits and pieces but nothing I've... (6 Replies)
i have a script that access the database and then returns some row. but in the command prompt it it not showing the column header. how to get that ?
below the script:
------------------------------------------------------------------------
#!/bin/ksh
.... (4 Replies)
Hi,
I have a system under test, and I use a script that does a ps.
The output, is in the following format, it's basically the timestamp, followed by the rss and vsize.
09:03:57 68404 183656 68312 181944 69860 217360 67536 182564 69072 183172 69032 199276
09:04:27 68752 183292 70000 189020... (5 Replies)
Hi Guys,
I am trying to convert a file which has a row based output to a column based output. My original file looks like this:
1
2
3
4
5
6
1
2
3
1
2
3 (8 Replies)
Hello All,
i have a file with the contents like shown below
Name = POLICY1
Selected = 1
Written = 0
Name = POLICY2
Selected = 6
Written = 8
Name = POLICY3
Selected = 4
Written = 26
I want the output to be... (5 Replies)
awk -v OFS="\t" -v ORS="\r\n" 'NR==FNR{A=$4; next} A {$4=$4 " " A}1' refseq_genes.txt LCH_exons.txt > output2.txt
Trying to output the data to separate columns in excel, but the 4th column seems to be merged together.
This is more of just a learning question. Thank you :). (1 Reply)
input1
john 20
bob 30
input2
john 60
bob 100
cat input1 >> output
cat input2 >> output
ouput
john 20
bob 30
john 60
bob 100
desired output
input1 input1 input2 input2
john 20 john 60 (3 Replies)
Discussion started by: quincyjones
3 Replies
LEARN ABOUT FREEBSD
gpioctl
GPIOCTL(1) BSD General Commands Manual GPIOCTL(1)NAME
gpioctl -- GPIO control utility
SYNOPSIS
gpioctl -l [-f ctldev] [-v]
gpioctl -t [-f ctldev] pin
gpioctl -c [-f ctldev] pin flag [flag ...]
gpioctl [-f ctldev] pin [0|1]
DESCRIPTION
The gpioctl utility could be used to manage GPIO pins from userland and list available pins.
The options are as follows:
-c pin flag [flag ...]
Configure pin by setting provided flags. The following flags are currently defined:
IN Input pin
OUT Output pin
OD Open drain pin
PP Push pull pin
TS Tristate pin
PU Pull-up pin
PD Pull-down pin
II Inverted input pin
IO Inverted output pin
-f ctldev GPIO controller device to use If not specified, defaults to /dev/gpioc0
-l list available pins
-t pin toggle value of provided pin number
-v be verbose: for each listed pin print current configuration
EXAMPLES
o List pins available on GPIO controller defined by device /dev/gpioc0
gpioctl -f /dev/gpioc0 -l
o Set the value of pin 12 to 1
gpioctl -f /dev/gpioc0 12 1
o Configure pin 12 to be input pin
gpioctl -f /dev/gpioc0 -c 12 IN
SEE ALSO gpio(4), gpioiic(4), gpioled(4)HISTORY
The gpioctl utility appeared in FreeBSD 9.0.
AUTHORS
The gpioctl utility and this manual page were written by Oleksandr Tymoshenko <gonzo@freebsd.org>.
BSD November 7, 2013 BSD