07-24-2013
Thanks for the replies.
I'm waiting for our Oracle support to be renewed, so until then it's hard to get something done with the existing hardware support team unless I can specifically point out some hardware is defective. This is the only Intel X4270 we have that's connected to SAN storage, most of our SAN-connected servers are SPARC. So I'm less familiar with this Intel hardware.
The SAN switches are zoned to specific servers.
9 More Discussions You Might Find Interesting
1. Linux
Hi
I have a linux box attched to a SAN storage from EMC with RAID 5 .I understand that it has 3g cache howver a 20gb file creation takes too much time here are my results any ideas why
time dd if=/dev/zero of=disk.img bs=1048576 count=20000
20000+0 records in
20000+0 records out
997.59s... (2 Replies)
Discussion started by: xiamin
2 Replies
2. Solaris
iostat -nE returns the followings
I want to know what is happening to my StorEDGE A1000?
Can someone help me? It is a critical device. (1 Reply)
Discussion started by: nickychung
1 Replies
3. Solaris
Hi all,
We have below WARNING in /var/adm/messages file from our Solaris server.
WARNING: /sbus@1f,0/SUNW,fas@e,8800000/sd@0,0 (sd0):
Error for Command: write(10) Error Level: Fatal
Requested Block: 16745265 Error Block: 16745269
Vendor: SEAGATE Serial Number:... (8 Replies)
Discussion started by: summerboy
8 Replies
4. Solaris
Good morning to one and all :-) Thank god its Friday, as its bee na rubbish week for me !
So, a quick question. Disks ! Ive got a few local disks, and a few SAN disks used on my solaris server. Whats confusing me, and Im not sure if there's an issue at the SAN end, or my end, regarding the... (3 Replies)
Discussion started by: sbk1972
3 Replies
5. Solaris
what is the difference between softerrors,harderrors,transport errors? (3 Replies)
Discussion started by: tv.praveenkumar
3 Replies
6. Solaris
I all,
I would like to know what are the causes of :
-soft error
-harderror
-transport error
and how to avoid and repare them.
I got the iostat out put below:
atng-mm01% iostat -En | grep -i hard
c0t0d0 Soft Errors: 1 Hard Errors: 0 Transport Errors: 0
c0t0d1 ... (3 Replies)
Discussion started by: zaza
3 Replies
7. UNIX for Dummies Questions & Answers
Hello everybody,
I'm using the binary inqraid (Linux RHEL) in order to retrieve information about SAN disks. The questions are:
Given an LDEV, how do I know if the SAN disk related to this LDEV is being used by the OS? I mean, how can I demonstrate to "Storage department" that all disks of... (4 Replies)
Discussion started by: asanchez
4 Replies
8. Red Hat
Hello,
How can I identify SAN disks not in use by the OS?
Thank you. (8 Replies)
Discussion started by: asanchez
8 Replies
9. UNIX for Dummies Questions & Answers
Hi Unix experts,
I have a question regarding a disk failure seen in "iostat -Enm" output:
# iostat -Enm
c1t0d0 Soft Errors: 0 Hard Errors: 7 Transport Errors: 9
Vendor: FUJITSU Product: MAU3073NCSUN72G Revision: 0802 Serial No: 0514F005M0
Size: 73.40GB <73400057856 bytes>
Media... (5 Replies)
Discussion started by: dyavuzy1
5 Replies
LEARN ABOUT FREEBSD
if_ix
IXGBE(4) BSD Kernel Interfaces Manual IXGBE(4)
NAME
ixgbe -- Intel(R) 10Gb Ethernet driver for the FreeBSD operating system
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ixgbe
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ixgbe_load="YES"
DESCRIPTION
The ixgbe driver provides support for PCI 10Gb Ethernet adapters based on the Intel 82598EB Intel(R) Network Connections. The driver sup-
ports Jumbo Frames, MSIX, TSO, and RSS.
For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements
listed apply to use with FreeBSD.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 16114.
This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).
HARDWARE
The ixgbe driver supports the following cards:
o Intel(R) 10 Gigabit XF SR/AF Dual Port Server Adapter
o Intel(R) 10 Gigabit XF SR/LR Server Adapter
o Intel(R) 82598EB 10 Gigabit AF Network Connection
o Intel(R) 82598EB 10 Gigabit AT CX4 Network Connection
DIAGNOSTICS
ixgbe%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ixgbe%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ixgbe%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection
(cable).
SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com.
If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information
related to the issue to <freebsd@intel.com>.
SEE ALSO
altq(4), arp(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)
HISTORY
The ixgbe device driver first appeared in FreeBSD 7.0.
AUTHORS
The ixgbe driver was written by Intel Corporation <freebsd@intel.com>.
BSD
December 19, 2010 BSD