Hi again!
I am still impressed how fast I get a solution for my topic "average specific column value awk" yesterday.
The associative arrays in awk work fine for me!
But now I have another question for the same project.
Now I have a list like this
How can I get the highest(H) and the lowest(h) value of the $2 column addicted to the values of
the $1 columns? My goal is to compute the difference between both and also to summarize all differences,
to get a scalar for an evaluation:
e.g.
(In the end I want to evaluate the averages from my last post with these scalars.)
Hi,
I have a file that looks like this:
s6 98
s6 91
s6 56
s5 32
s5 10
s5 4
So what I want to do is print only the highest value for each value in the column:
So the file will look like this:
s6 98
s5 32
Thanks (4 Replies)
Hi all,
I have a large column of numbers like
5.6789
2.4578
9.4678
13.5673
1.6589
.....
I am trying to make an awk code so that awk can easily go through the column and arrange the numbers from least to highest like
1.6589
2.4578
5.6789
.......
can anybody suggest, how can I do... (5 Replies)
Hi everyone,
This is my first post, but I have already received a lot of help from the forums in the past. Thanks!
I've searched the forums and my question is very similar to an earlier post entitled "Printing highest value from one column", which I am apparently not yet allowed to post a... (1 Reply)
Hi,
I have a file with the following columns:
361459 447394 CHL1
290282 290282 CHL1
361459 447394 CHL1
361459 447394 CHL1
178352861 178363529 AGA
178352861 178363529 AGA
178363657 178363657 AGA
Essentially, using CHL1 as an example. For any line that has CHL1 in... (2 Replies)
Hi, I want to extract the the top 10 and lowest 10 percentile for a column of values.
For example in column 2 for this file:
JOE 1
JAY 5
JAM 6
JIL 8
JIB 4
JIH 3
JIG 2
JIT 7
JAM 9
MAR 10
The top 10 lowest will be:
JOE 1
and the top 10 highest will be: (2 Replies)
I have a file like:
I would like to find lines lines with duplicate values in column 1, and retain only one based on two conditions: 1) keep line with highest value in column 3, 2) if column 3 values are equal, retain the line with the highest value in column 4.
Desired output:
I was able to... (3 Replies)
Hi Guys,
I am looking for a way to sort the output below from the "Inuse" count from Highest to Lowest. Is it possible?
Thanks in advance.
user1 0.12 0.06 0 0.12
User Inuse Pin Pgsp Virtual
Unit:... (4 Replies)
Hi, I have a little issue right now.
I have a file with 4 columns
test0000002,10030010330,c_,218
test0000002,10030010330,d_,202
test0000002,10030010330,b_,193
test0000002,10030010020,c_,178
test0000002,10030010020,b_,170
test0000002,10030010330,a_,166
test0000002,10030010020,a_,151... (2 Replies)
Hi, I have a little issue right now.
I have a file with 4 columns
test0000002,10030010330,c_,218
test0000002,10030010330,d_,202
test0000002,10030010330,b_,193
test0000002,10030010020,c_,178
test0000002,10030010020,b_,170
test0000002,10030010330,a_,166
test0000002,10030010020,a_,151... (3 Replies)
Discussion started by: Ebk
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)