07-09-2013
Problems with wlan0 configuration
Hi I'm getting some troubles trying to create a Debian wheeze 7 from a vm using VMware from a laptop which I get lan and internet connection by a wireless router.
The first problem is that I'm a bit lost trying to configure the wlan to get lan and internet connection.
I've read about that I gotta install wpasupplicant but when I've tried to do as root user apt-get install wpasupplicant and I've got a message like this:
"Package wpasupplicant is not available, but is referred to another package. This may mean that the package is missing, has been obsoleted or is only available in from another source
E: Package 'wpasupplicant' has no installation candidate"
On the other hand, could someone tell me how to configure /etc/network/interfaces and etc/resolv.conf (if this is necessary) after the last step?. I have a router with WPA2-PSK password and I'm using DHCP
Well sorry try to understand that I'm a guy learning on my own at home and a beginner!
Thank you so much for reading and answer!
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
First of all, Happy Holidays,Merry Xmas, Happy Hanakah, Happy Kwanzaa, Happy Mid Winter Festival, etc.(Forgive me if I left your holiday out)
Anyway, here is my situation. I am setting up an email server at the job, and Sendmail is not cooperating. The error that I get on my RedHat 7.3 Dell... (5 Replies)
Discussion started by: Jody
5 Replies
2. BSD
I had just instal freebsd in my computer, wich is very nice,am very happy about it, am new to the unix os and i know unmost nothing and my problem is that i din't do i good configuration because i can get internet when i open the webbrowser, a have a yahoo dsl connection, i can't even play a cd in... (0 Replies)
Discussion started by: nobody
0 Replies
3. BSD
is me again guys, sorry for the mistake in the written, what the problem is, i can't connect to the internet because i did a bad configuration in the freebsd os, i use a yahoo dsl modem and i don't dial to my isp, but everytime i try to connect ask me for a phone number to connect to my isp, what... (1 Reply)
Discussion started by: nobody
1 Replies
4. UNIX for Dummies Questions & Answers
Hello.
I'm currently usng Solaris 10 and have to configure the box so that it acts as an FTP server handling multiple virtual domains. This should be done using wu-ftpd.
I have successfully configured the box to be able to handle multiple virtual FTP servers, and all works well when I log in as... (2 Replies)
Discussion started by: CowsUdders
2 Replies
5. AIX
Hi,
I have a strange problem. we're trying to connect an IBM pseries, to a Brocade switch, for SAN acess, using a badged emulex card, (IBM FC6239) WE can configure the device to see the fabric. The only problem we have is that the Brocade sees the HBA as storage, and not as a HBA.
We've zoned... (1 Reply)
Discussion started by: praxis22
1 Replies
6. UNIX for Advanced & Expert Users
Is there a time limit ifconfig wlan0 down? I used that command to take my wireless down.
sudo ifconfig wlan0 downWhen I came back about 6 hours later it was working without me bringing my wireless back up. I am the only one that uses my computer or that knows the root password. (0 Replies)
Discussion started by: cokedude
0 Replies
7. Red Hat
Hi All,
Am using Toshiba Satellite C850-l5212 Laptop . I have installed RHEL6 server on it ( Linux 2.6.32-220.el6.x86_64 )
I Installed wireless driver ( linux_mac80211_0012.0207.2013.tar.bz2 ) and the installation went fine.
But when i do ifconfig wlan0 up its giving the below error .... (0 Replies)
Discussion started by: senthilcaesar
0 Replies
8. Debian
Dear Moderator,
While working on airmon-ng when the situation has come to set wlan0 on monitor mode
Identification Wlan0
root@kali:~# iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated ... (1 Reply)
Discussion started by: raghunsi
1 Replies
9. Linux
I have created a bridge with nmcli between eth0 and wlan0
I use this procedure
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT SUSE
ifcfg-wireless
IFCFG(5) Network configuration IFCFG(5)
NAME
ifcfg-wireless - wireless LAN network interface configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-wlan-*
/etc/sysconfig/network/ifcfg-type-wlan
GENERAL
Wireless networks need some additional configuration data compared to ethernet ones. Therefore additional variables for ifcfg files were
introduced. All wireless LAN specific variables are described in the ifcfg template file /etc/sysconfig/network/ifcfg.template. It is pos-
sible to configure more than one wireless network accepted for association. To achieve this add suffix _1 to all wireless variables for the
second network, _2 for the this, and so on. Example: WIRELESS_ESSID_1="second_net" You can have up to ten wireless networks configured.
Some wireless variables are not applicable to a single wireless network but are global to the interface. The description of the variable
points this out.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Michal Svec <msvec@suse.cz> -- ifup script
Bjoern Jacke -- ifup script
Mads Martin Joergensen <mmj@suse.de> -- ifup manual page
Michal Ludvig <mludvig@suse.cz> -- tunnel support
Joachim Gleissner <jg@suse.de> -- wireless support
SEE ALSO
ifup(8).
sysconfig December 2005 IFCFG(5)