06-27-2013
Thank you Peasant, "
aggregation" is the right word. What was I thinking with "multicast-ing"?
Thank you, -you got me pointed I the right direction. Time for some reading. -KJ
9 More Discussions You Might Find Interesting
1. Solaris
can someone please through light on how to configure video and nic.
Dimension 3000 Series, Intel Pentium 4 Processor at 2.8GHz
256MB DDR SDRAM at 400MHz EA 0.00 0.00
17 in (17 in viewable) E173FP Flat Panel Display EA
Integrated Intel Extreme Graphics 2 EA
Intel Pro 100M Integrated... (4 Replies)
Discussion started by: Jimmpy
4 Replies
2. Solaris
I wanted to configure a second NIC card on a different IP on my Sun E450 server.
Currently, I have hme0.
when I ran the command : ifconfig hme1 <ip address> netmask <subnet mask> broadcast + up
I got the following error message: ifconfig: SIOCGIFFLAGS: hme1: no such interface
Any idea... (3 Replies)
Discussion started by: Remi
3 Replies
3. SuSE
Hi all,
i tried to set up two network cards in Linux. During installation, it can detect both; eth0 and eth1. In the GUI, i can click on eth0 and type in the IP add and netmask. In the lower half of the window, I can also enter the gateway,hostname,and DNS servers
When i click on eth1, i can... (5 Replies)
Discussion started by: new2ss
5 Replies
4. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT DEBIAN
colorgccrc
COLORGCCRC(5) File Formats Manual COLORGCCRC(5)
NAME
colorgccrc - configuration file for colorgcc
DESCRIPTION
A colorgccrc configuration file is used to configure the highlighting of the compiler output from colorgcc.
SYNTAX
Each line consists of a keyword designating a configuration variable. The keyword is followed by `:' and then one or several values
(depending on the keyword). Lines beginning with a hash mark `#' are comments.
CONFIGURATION VARIABLES
g++ | gcc | c++ | cc | g77 | gcj | gnat | gpc
Specifies the paths to the compilers. Takes one value; a path to the compiler.
nocolor
Specifies what terminal types colorization should be disabled on. Takes one or several values, separated by whitespace.
srcColor
Specifies the highlighting attributes source-code should be given. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
introColor
Specifies the highlighting attributes for normal compiler output. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
warningFileNameColor | errorFileNameColor
Specifies the highlighting attributes for the filename in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningNumberColor | errorNumberColor
Specifies the highlighting attributes for the line-number in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningMessageColor | errorMessageColor
Specifies the highlighting attributes for the message-text in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
COLOR ATTRIBUTES
The following attributes are valid for highlighting.
clear, reset
bold, underline, underscore, blink, reverse, concealed
black, red, green, yellow, blue, magenta, cyan, white
on_black, on_red, on_green, on_yellow, on_blue, on_magenta, on_cyan, on_white
SEE ALSO
gcc(1), colorgcc(1)
HISTORY
Jan 15 2003: Initial version of this manual-page.
REPORTING BUGS
Report bugs to <jmoyers@geeks.com>
AUTHORS
Jamie Moyers <jmoyers@geeks.com> is the author of colorgcc.
This manual page was written by Joe Wreschnig <piman@sacredchao.net>, and modified by David Weinehall <tao@debian.org>, for the Debian
GNU/Linux system (but may be used by others).
COPYRIGHT
Copyright (C) 2003 Jamie Moyers
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU-
LAR PURPOSE.
Jan 15, 2003 COLORGCCRC(5)