06-27-2013
Thank you Peasant, "
aggregation" is the right word. What was I thinking with "multicast-ing"?
Thank you, -you got me pointed I the right direction. Time for some reading. -KJ
9 More Discussions You Might Find Interesting
1. Solaris
can someone please through light on how to configure video and nic.
Dimension 3000 Series, Intel Pentium 4 Processor at 2.8GHz
256MB DDR SDRAM at 400MHz EA 0.00 0.00
17 in (17 in viewable) E173FP Flat Panel Display EA
Integrated Intel Extreme Graphics 2 EA
Intel Pro 100M Integrated... (4 Replies)
Discussion started by: Jimmpy
4 Replies
2. Solaris
I wanted to configure a second NIC card on a different IP on my Sun E450 server.
Currently, I have hme0.
when I ran the command : ifconfig hme1 <ip address> netmask <subnet mask> broadcast + up
I got the following error message: ifconfig: SIOCGIFFLAGS: hme1: no such interface
Any idea... (3 Replies)
Discussion started by: Remi
3 Replies
3. SuSE
Hi all,
i tried to set up two network cards in Linux. During installation, it can detect both; eth0 and eth1. In the GUI, i can click on eth0 and type in the IP add and netmask. In the lower half of the window, I can also enter the gateway,hostname,and DNS servers
When i click on eth1, i can... (5 Replies)
Discussion started by: new2ss
5 Replies
4. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT DEBIAN
set_color
set_color(1) fish set_color(1)
NAME
set_color - set_color - set the terminal color
set_color - set the terminal color
Synopsis
set_color [-v --version] [-h --help] [-b --background COLOR] [COLOR]
Description
Change the foreground and/or background color of the terminal. COLOR is one of black, red, green, brown, yellow, blue, magenta, purple,
cyan, white and normal.
o -b, --background Set the background color
o -c, --print-colors Prints a list of all valid color names
o -h, --help Display help message and exit
o -o, --bold Set bold or extra bright mode
o -u, --underline Set underlined mode
o -v, --version Display version and exit
Calling set_color normal will set the terminal color to whatever is the default color of the terminal.
Some terminals use the --bold escape sequence to switch to a brighter color set. On such terminals, set_color white will result in a grey
font color, while set_color --bold white will result in a white font color.
Not all terminal emulators support all these features. This is not a bug in set_color but a missing feature in the terminal emulator.
set_color uses the terminfo database to look up how to change terminal colors on whatever terminal is in use. Some systems have old and
incomplete terminfo databases, and may lack color information for terminals that support it. Download and install the latest version of
ncurses and recompile fish against it in order to fix this issue.
Version 1.23.1 Sun Jan 8 2012 set_color(1)