Configure Second NIC on HP UX? Post: 302826489

9 More Discussions You Might Find Interesting

1. Solaris

Cant configure video & nic (solaris 8 on x86)

can someone please through light on how to configure video and nic. Dimension 3000 Series, Intel Pentium 4 Processor at 2.8GHz 256MB DDR SDRAM at 400MHz EA 0.00 0.00 17 in (17 in viewable) E173FP Flat Panel Display EA Integrated Intel Extreme Graphics 2 EA Intel Pro 100M Integrated...

2. Solaris

Configure second NIC on Sun E450

I wanted to configure a second NIC card on a different IP on my Sun E450 server. Currently, I have hme0. when I ran the command : ifconfig hme1 <ip address> netmask <subnet mask> broadcast + up I got the following error message: ifconfig: SIOCGIFFLAGS: hme1: no such interface Any idea...

3. SuSE

2 NIC in linux

Hi all, i tried to set up two network cards in Linux. During installation, it can detect both; eth0 and eth1. In the GUI, i can click on eth0 and type in the IP add and netmask. In the lower half of the window, I can also enter the gateway,hostname,and DNS servers When i click on eth1, i can...

4. Solaris

Cause of NIC changes ...?

Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1... But instead the ext PCI takes precedence in the order and the Net0 becomes...

5. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

6. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

7. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

8. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

LEARN ABOUT CENTOS

idevicebackup2

idevicebackup2(1)					      General Commands Manual						 idevicebackup2(1)

NAME

       idevicebackup2 - Create or restore backups for devices running iOS 4 or later.

SYNOPSIS

       idevicebackup2 [OPTIONS] CMD [CMDOPTIONS] DIRECTORY

DESCRIPTION

       Create or restore backup from the current or specified directory.

OPTIONS

       -u, --udid UDID
	      target specific device by its 40-digit device UDID.

       -s, --source UDID
	      use backup data from device specified by UDID.

       -i, --interactive
	      request passwords interactively on the command line.

       -d, --debug
	      enable communication debugging.

       -h, --help
	      prints usage information.

COMMANDS

       backup create backup for the device.

       restore
	      restore last backup to the device.

	    --system
	      restore system files, too.

	    --reboot
	      reboot the system when done.

	    --copy
	      create a copy of backup folder before restoring.

	    --settings
	      restore device settings from the backup.

	    --remove
	      remove items which are not being restored.

	    --password PWD
	      supply the password of the source backup.

       info   show details about last completed backup of device.

       list   list files of last completed backup in CSV format.

       encryption on|off [PWD]
	      enable or disable backup encryption.

       changepw [OLD NEW]
	      change backup password on target device.

AUTHORS

       Martin Szulecki

       Nikias Bassen

SEE ALSO

       idevicebackup(1)

																 idevicebackup2(1)