06-20-2013
Brilliant!
thank you so much!
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi,
i'm new here (and to scripting too).
I was hoping for some help in comparing two files.
i have a file called 'file1' with a list of names in the following format:
adam jones
paul higgins
kelly lowe
i also have another file which may contain some of the names but with a lot of... (4 Replies)
Discussion started by: ibking
4 Replies
2. Shell Programming and Scripting
Hi, I have two files file1 and file2. I have to merge the columns of those two files into file3 based on common column of two files. To be simple.
file1:
Row-id name1
13456 Rahul
16789 Vishal
18901 Karan
file2 :
Row-id place
18901 Mumbai
... (2 Replies)
Discussion started by: manneni prakash
2 Replies
3. UNIX for Dummies Questions & Answers
Dear Friends,
I really do not know Linux and I really would like to understand it because it does help to work with large data. I am reading this forum for 1 week to try a solution for my problem. I think that, using others post informations, I was almost there...
I have 2 big tables... (4 Replies)
Discussion started by: lColli
4 Replies
4. Shell Programming and Scripting
Hi All,
I do have 2 files
file 1 has 4 tab delimited columns
234 a c dfgyu
294 b g fih
302 c h jzh
328 z c san
597 f g son
File 2 has 2 tab delimted columns
234 23
302 24
597 24
I want to merge file 2 with file 1 based on the data common in both files which is the first column so... (6 Replies)
Discussion started by: Lucky Ali
6 Replies
5. Shell Programming and Scripting
Hi all,
I have created 3 arrays which can have common elements in each like-
arr_a contains str1 str2 str3 str4 str5
arr_b contains str3 str6 str7 str1 str8
arr_c contains str4 str9 str10 str2
each array is created with "set -A arr_name values" command. I want to create a resultant array-say... (1 Reply)
Discussion started by: sanzee007
1 Replies
6. Shell Programming and Scripting
Hi, I am trying to merge information across 2 files. The first file is a "master" file, with all IDS. File 2 contains a subset of IDs of those in File 1.
I would like to match up individuals in File 1 and File 2, and add information in File 2 to that of File 1 if they appear. However, if an... (3 Replies)
Discussion started by: hubleo
3 Replies
7. Shell Programming and Scripting
Hi
I have file1 as
IJU_NSOMOW;
SOWWOD_TWUIQ;
and file2 as
how are you?;
fine there;
Now my problem is i need the output file as
IJU_NSOMOW; how are you?;
SOWWOD_TWUIQ; fine there; (2 Replies)
Discussion started by: Priya Amaresh
2 Replies
8. Shell Programming and Scripting
HI, I have a 3-column tab separated column (approx 1GB) in which I would like to count and output the frequency of all of the common elements in the 1st column.
For instance:
If my input was the following:
dot is-big 2
dot is-round 3
dot is-gray 4
cat is-big 3
hot in-summer 5
My... (4 Replies)
Discussion started by: owwow14
4 Replies
9. Shell Programming and Scripting
I would like to merge two tables based on column 1:
File 1:
1 today
1 green
2 tomorrow
3 red
File 2:
1 a lot
1 sometimes
2 at work
2 at home
2 sometimes
3 new
4 a lot
5 sometimes
6 at work (4 Replies)
Discussion started by: BSP
4 Replies
10. Shell Programming and Scripting
I have an array code and output is below:
echo $1
while read -r fline; do
echo "%%%%%%$fline%%%%%"
fmy_array+=("$fline")
done <<< "$1"
Output:
CR30903 YU0007 SRIL CR30903 Yogesh SRIL
%%%%%%CR30903 YU0007 SRIL%%%%%
%%%%%%CR30903 Yogesh SRIL%%%%%
... (8 Replies)
Discussion started by: mohtashims
8 Replies
LEARN ABOUT CENTOS
arping
ARPING(8) System Manager's Manual: iputils ARPING(8)
NAME
arping - send ARP REQUEST to a neighbour host
SYNOPSIS
arping [-AbDfhqUV] [-c count] [-w deadline] [-s source] -I interface destination
DESCRIPTION
Ping destination on device interface by ARP packets, using source address source.
OPTIONS
-A The same as -U, but ARP REPLY packets used instead of ARP REQUEST.
-b Send only MAC level broadcasts. Normally arping starts from sending broadcast, and switch to unicast after reply received.
-c count
Stop after sending count ARP REQUEST packets. With deadline option, arping waits for count ARP REPLY packets, until the timeout
expires.
-D Duplicate address detection mode (DAD). See RFC2131, 4.4.1. Returns 0, if DAD succeeded i.e. no replies are received
-f Finish after the first reply confirming that target is alive.
-I interface
Name of network device where to send ARP REQUEST packets.
-h Print help page and exit.
-q Quiet output. Nothing is displayed.
-s source
IP source address to use in ARP packets. If this option is absent, source address is:
o In DAD mode (with option -D) set to 0.0.0.0.
o In Unsolicited ARP mode (with options -U or -A) set to destination.
o Otherwise, it is calculated from routing tables.
-U Unsolicited ARP mode to update neighbours' ARP caches. No replies are expected.
-V Print version of the program and exit.
-w deadline
Specify a timeout, in seconds, before arping exits regardless of how many packets have been sent or received. In this case arping
does not stop after count packet are sent, it waits either for deadline expire or until count probes are answered.
SEE ALSO
ping(8), clockdiff(8), tracepath(8).
AUTHOR
arping was written by Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>. It is now maintained by YOSHIFUJI Hideaki <yoshfuji@skbuff.net>.
SECURITY
arping requires CAP_NET_RAW capability to be executed. It is not recommended to be used as set-uid root, because it allows user to modify
ARP caches of neighbour hosts.
AVAILABILITY
arping is part of iputils package and the latest versions are available in source form at http://www.skbuff.net/iputils/iputils-cur-
rent.tar.bz2.
iputils-121221 10 June 2014 ARPING(8)