Most processes have no hard limit configured.
32-bit processes have a 4 GiB technical limit.
Java processes (JVMs) have a hard limit for their heap size set with the -Xmx option. It is normally set in the script that launch them.
Please post:
output after replacing pid by the process id of the java command you are investigating (was 12503).
thanks very much jlliagre and herpg.
please share some commands to investigate a process, memory utilization of pid.
Hello,
The last line of prstat shows load average.
I am unable to figure out what actually it is.
I have read the man pages and also googled, all for no use.
Can somebody help me, as to what should be the avg. load of the system for best performance and how is this load of prstat calculated. (6 Replies)
Discussion started by: vibhor_agarwali
6 Replies
2. Post Here to Contact Site Administrators and Moderators
Hello and thanks in advance.
I have a Sun box with raid 1 on the O/S disks using solaris svm.
I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space.
I have been warned not to do this by some... (3 Replies)
Good Evening everyone,
I am confused about prstat O/P as it shows memory values which are different from actual value.Below is the O/P of prstat command and swap commands.
NPROC USERNAME SIZE RSS MEMORY TIME CPU
48 root 2113M 1590M 1.2% 45:09.39 32%
31 daemon ... (7 Replies)
free -m : 1023 total swap space
created default partition /dev/sdb1 50M using fdisk. i did write the changes.
#mkswap /dev/sdb1
#swapon /dev/sdb1
free -m : 1078 total swap space
this shows that the swap is on
Question : i did not change the type LINUX SWAP (82) in fdisk.
so why is... (5 Replies)
Hi
I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system:
- I would like to know when does the memory swap space spill over to the device swap space?
- And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
Hi,
I have some question about memory in Solaris.
How it's possible that prstat -a show me that some process using 230M RSS and when I'm using pmap -x show me that this same process using only 90M RSS ? (0 Replies)
Hi everyone,
was hoping someone might be able to help me understand what I am seeing on one of our solaris systems.
prstat -s size -a is showing user oradba as being top virtual memory consumption.
639 oradba 3012G 2951G 100% 59:44:01 25%
why is it saying 3012G size and 2951G RSS... (6 Replies)
Hi,
When I sum the RSS number in the ps command for a specific user and compare it with the RSS values of the prstat command of the same user - there is a big difference.
Server details: Solaris 10 5/09 s10s_u7wos_08 SPARC
prstat output:
NPROC USERNAME SWAP RSS MEMORY TIME ... (2 Replies)
Hi Solaris Folks :),
I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands.
$swap -s
total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available
$swap -l
swapfile dev swaplo... (6 Replies)
Discussion started by: seenuvasan1985
6 Replies
LEARN ABOUT HPUX
plimit
plimit(1) User Commands plimit(1)NAME
plimit - get or set the resource limits of running processes
SYNOPSIS
plimit [-km] pid...
plimit {-cdfnstv} soft,hard... pid...
DESCRIPTION
If one or more of the cdfnstv options is specified, plimit sets the soft (current) limit and/or the hard (maximum) limit of the indicated
resource(s) in the processes identified by the process-ID list, pid. Otherwise plimit reports the resource limits of the processes identi-
fied by the process-ID list, pid.
Only the owner of a process or the super-user is permitted either to get or to set the resource limits of a process. Only the super-user
can increase the hard limit.
OPTIONS
The following options are supported:
-k On output, show file sizes in kilobytes (1024 bytes) rather than in 512-byte blocks.
-m On output, show file and memory sizes in megabytes (1024*1024 bytes).
The remainder of the options are used to change specified resource limits. They each accept an argument of the form:
soft,hard
where soft specifies the soft (current) limit and hard specifies the hard (maximum) limit. If the hard limit is not specified, the comma
may be omitted. If the soft limit is an empty string, only the hard limit is set. Each limit is either the literal string unlimited, or a
number, with an optional scaling factor, as follows:
nk n kilobytes
nm n megabytes (minutes for CPU time)
nh n hours (for CPU time only)
mm:ss minutes and seconds (for CPU time only)
The soft limit cannot exceed the hard limit.
-c soft,hard Set core file size limits (default unit is 512-byte blocks).
-d soft,hard Set data segment (heap) size limits (default unit is kilobytes).
-f soft,hard Set file size limits (default unit is 512-byte blocks).
-n soft,hard Set file descriptor limits (no default unit).
-s soft,hard Set stack segment size limits (default unit is kilobytes).
-t soft,hard Set CPU time limits (default unit is seconds).
-v soft,hard Set virtual memory size limits (default unit is kilobytes).
OPERANDS
The following operands are supported.
pid Process ID list.
EXIT STATUS
plimit returns the exit value zero on success, non-zero on failure (such as no such process, permission denied, or invalid option).
FILES
/proc/pid/* process information and control files
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWesu |
+-----------------------------+-----------------------------+
SEE ALSO ulimit(1), proc(1), getrlimit(2), setrlimit(2), proc(4), attributes(5),
SunOS 5.10 8 Jun 1998 plimit(1)