The issue has been resolved. According to the documentation/tutorial referenced in my opening post, it mentioned to issue the following commands (which I did):
However; on Oracle's site, regarding the eeprom(1M)command it mentions the following:
Quote:
ttya-ignore-cd If true, operating system ignores carrier-detect on TTYA. Defaults to true.
ttya-rts-dtr-off If true, operating system does not assert DTR and RTS on TTYA. Defaults to false.
Therefore setting both to false allowed both carrier detection and DTR to be asserted in Solaris.
Hello There,
I configure my Modem as follow.
Step1.
# admintool &
Then from Browse --> Serial Port
i select tta port and Edit --> Modify
From that i select Template : Modem:Dial Out
Baud Rate: 9600
Ok
Step 2
# tip /dev/cua/a
connected (1 Reply)
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Friends,
I am facing a problem in connecting two SCO Openserver 5.0.6 servers through Dial-Up connectivity as is done in the case of two Windows PCs. Please help me out with the following problems:
(a) How to configure the modem?
(b) How to setup a Dial-In connection?
(c) How to... (1 Reply)
hi all..
sorry for repeating the same question many times,
i just set up a null modem, i am using this as reference :
DB25 DB9
-- -
2 TD ---- 2 RD
3 RD ---- 3 TD
4 RTS ---- 8 CTS
5 CTS ---- 7 RTS
7 GND ---- 5 GND
6 DSR -+
+--- 4 DTR
8... (0 Replies)
Dear All,
i have problem during install modem dial up with smc in solaris 10.
i can't find "login" because it's stop in _receive started transmit started.
thanks for your attention.
this is the list during i dial to this number :
altconn called
Device Type ACU wanted... (0 Replies)
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Hello to all,
I have one problem and hope you'll be able to help me.
It's about connecting Windows PC machine to Unix machine via dial up through Hyper terminal.
Connection was working in the past. In the meantime, windows machine is replaced (win XP) and unix machine stayed as is. So nothing is... (1 Reply)
Regarding carrier detection on FreeBSD 9.1 being run within Virtual Box:
I used a usb-serial dongle which shows up as ttyu0 on the BSD machine. Carrier detection appears to work. When I establish a null modem connection I receive a login prompt. If I login, and then unplug and plug back the... (2 Replies)
Discussion started by: rstor
2 Replies
LEARN ABOUT DEBIAN
device::modem::usrobotics
Device::Modem::UsRobotics(3pm) User Contributed Perl Documentation Device::Modem::UsRobotics(3pm)NAME
Device::Modem::UsRobotics - USR modems extensions to control self-mode
SYNOPSIS
use Device::Modem::UsRobotics;
my $modem = new Device::Modem::UsRobotics( port => '/dev/ttyS1' );
$modem->connect( baudrate => 9600 );
my %info = $modem->messages_info();
print "There are $info{unreleased_voice_msg} unread voice messages on $info{stored_voice_msg} total
";
print "There are $info{unreleased_fax_msg} unread fax messages on $info{stored_fax_msg} total
";
# Get details about message n. X
my %msg = $modem->message_info(1);
index type information attributes status day hour minute
callerid page addresshigh addresslow checksum
print 'This is a ', ($msg{type} == 2 ? 'voice' : 'fax'), 'message', "
";
print 'It came from no. ', $msg{callerid}, "
";
# ...
# Now clear all messages
$modem->clear_memory();
WARNING
This module is not documented yet, and it is a rough work in progress. Until now, it correctly reads voice/fax messages information, but
when saving voice messages to disk, sometimes they are incorrectly decoded.
So, if you need a working program, check out the good old TkUsr by Ludovic Drolez, unless you want to help develop
Device::Modem::UsRobotics.
DOCS TO BE COMPLETED FROM NOW.....
Yes, I'm a bad boy :-)
DESCRIPTION
Bla Bla Bla...
METHODS
clear_memory()
Used to permanently clear the memory space of the modem. There are separate memory spaces, one for voice/fax messages and one for user set-
tings. Examples:
$modem->clear_memory('user'); # or $modem->clear_memory(1)
$modem->clear_memory('messages'); # or $modem->clear_memory(2)
To clear both, you can use:
$modem->clear_memory('all'); # or $modem->clear_memory(0);
Parameters:
$memtype
String or integer that selects the type of memory to be cleared, where 0 is for "all", 1 is for "user" memory, 2 is for "messages" mem-
ory.
SUPPORT
Please feel free to contact me at my e-mail address cosimo@cpan.org for any information, to resolve problems you can encounter with this
module or for any kind of commercial support you may need.
AUTHOR
Cosimo Streppone, cosimo@cpan.org
COPYRIGHT
(C) 2004-2005 Cosimo Streppone, cosimo@cpan.org
This library is free software; you can only redistribute it and/or modify it under the same terms as Perl itself.
SEE ALSO
Device::Modem, perl
perl v5.8.8 2005-04-30 Device::Modem::UsRobotics(3pm)