|
|
Sponsored Content
Operating Systems
Solaris
Carrier Detection in Solaris 8 for Dial in and Null Modem Connections
Post 302821417 by DGPickett on Friday 14th of June 2013 01:29:33 PM
06-14-2013
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello There,
I configure my Modem as follow.
Step1.
# admintool &
Then from Browse --> Serial Port
i select tta port and Edit --> Modify
From that i select Template : Modem:Dial Out
Baud Rate: 9600
Ok
Step 2
# tip /dev/cua/a
connected (1 Reply)
Discussion started by: abidmalik
1 Replies
2. UNIX for Dummies Questions & Answers
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies
3. UNIX for Dummies Questions & Answers
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Discussion started by: Synbios
0 Replies
4. SCO
Friends,
I am facing a problem in connecting two SCO Openserver 5.0.6 servers through Dial-Up connectivity as is done in the case of two Windows PCs. Please help me out with the following problems:
(a) How to configure the modem?
(b) How to setup a Dial-In connection?
(c) How to... (1 Reply)
Discussion started by: thecobolguy
1 Replies
5. Solaris
hi all..
sorry for repeating the same question many times,
i just set up a null modem, i am using this as reference :
DB25 DB9
-- -
2 TD ---- 2 RD
3 RD ---- 3 TD
4 RTS ---- 8 CTS
5 CTS ---- 7 RTS
7 GND ---- 5 GND
6 DSR -+
+--- 4 DTR
8... (0 Replies)
Discussion started by: waterbear
0 Replies
6. Solaris
Dear All,
i have problem during install modem dial up with smc in solaris 10.
i can't find "login" because it's stop in _receive started transmit started.
thanks for your attention.
this is the list during i dial to this number :
altconn called
Device Type ACU wanted... (0 Replies)
Discussion started by: mr.ridho
0 Replies
7. IP Networking
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
8. UNIX for Advanced & Expert Users
Hello to all,
I have one problem and hope you'll be able to help me.
It's about connecting Windows PC machine to Unix machine via dial up through Hyper terminal.
Connection was working in the past. In the meantime, windows machine is replaced (win XP) and unix machine stayed as is. So nothing is... (1 Reply)
Discussion started by: Mick
1 Replies
9. BSD
Regarding carrier detection on FreeBSD 9.1 being run within Virtual Box:
I used a usb-serial dongle which shows up as ttyu0 on the BSD machine. Carrier detection appears to work. When I establish a null modem connection I receive a login prompt. If I login, and then unplug and plug back the... (2 Replies)
Discussion started by: rstor
2 Replies
LEARN ABOUT ULTRIX
mdc
mdc(4) Kernel Interfaces Manual mdc(4) Name mdc - DS5100 serial line driver Syntax device mdc0 at ibus? vector mdcintr device mdc1 at ibus? vector mdcintr device mdc2 at ibus? vector mdcintr Description A DS5100 base system (mdc0) provides four asynchronous ports. An optional asynchronous card (mdc1 and mdc2 ) can be added to supply eight additional ports. The mdc ports are used as follows: Port Usage Connector 0 Console port 6-pin MMJ on CPU board 1 Local terminal 6-pin MMJ on CPU board 2 Full modem control port 25-pin D-Sub on CPU board 3 Local terminal 6-pin MMJ on CPU board An optional asynchronous board provides an additional eight lines: 4 Local terminal 6-pin MMJ 5 Local terminal 6-pin MMJ 6 Full modem control port 25-pin D-Sub 7 Local terminal 6-pin MMJ 8 Local terminal 6-pin MMJ 9 Local terminal 6-pin MMJ 10 Local terminal 6-pin MMJ 11 Local terminal 6-pin MMJ The console baud rate is set to 9600 baud by default. You can change this by setting the baud environment variable from console prompt. Each communication port from the serial line controller behaves as described in the reference page and can be set to run at any of 16 speeds. For the encoding, see You can establish the state of port 2 (port 6) by specifying either modem or nomodem as part of the file entry. Restrictions The speed default is to 9600 baud on the console port. The console device must be set for 8-bit character length with one stop bit and no parity. The driver enforces these restrictions; that is, changing speeds with the command may not always work on console ports. Files Console terminal Full modem control or local terminal See Also console(4), devio(4), tty(4), ttys(5), MAKEDEV(8) RISC mdc(4)