Sponsored Content
Operating Systems Solaris Carrier Detection in Solaris 8 for Dial in and Null Modem Connections Post 302820939 by DGPickett on Thursday 13th of June 2013 05:00:08 PM
Old 06-13-2013
A null modem is two cable heads and some wires. You can force CD true all the time with wiring it to DTR on the other side (if the other side powers off, there is no carrier). Wiring plans vary. Similar rules apply to other leads. Wiring varies to simulate a half duplex switched carrier modem as opposed to a full duplex continuous carrier modem. With the right wiring, it should be a rock. https://en.wikipedia.org/wiki/Null_modem Two DTE's, each pretending to be DCE to the other. https://en.wikipedia.org/wiki/RS-232
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Got connected with Modem but cannot dial Telephone no. to connect to host

Hello There, I configure my Modem as follow. Step1. # admintool & Then from Browse --> Serial Port i select tta port and Edit --> Modify From that i select Template : Modem:Dial Out Baud Rate: 9600 Ok Step 2 # tip /dev/cua/a connected (1 Reply)
Discussion started by: abidmalik
1 Replies

2. UNIX for Dummies Questions & Answers

Hyperterminal null modem connection to Solaris

I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up. I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies

3. UNIX for Dummies Questions & Answers

Dial-Up Modem

Im using Kinternet with a Lucent modem on Suse 9.0 Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0 This is the log that Kinternet gives after trying to connect: SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux. Status... (0 Replies)
Discussion started by: Synbios
0 Replies

4. SCO

Dial-Out & Dial-In Connections in OpenServer 5.0.6.

Friends, I am facing a problem in connecting two SCO Openserver 5.0.6 servers through Dial-Up connectivity as is done in the case of two Windows PCs. Please help me out with the following problems: (a) How to configure the modem? (b) How to setup a Dial-In connection? (c) How to... (1 Reply)
Discussion started by: thecobolguy
1 Replies

5. Solaris

null modem for testing

hi all.. sorry for repeating the same question many times, i just set up a null modem, i am using this as reference : DB25 DB9 -- - 2 TD ---- 2 RD 3 RD ---- 3 TD 4 RTS ---- 8 CTS 5 CTS ---- 7 RTS 7 GND ---- 5 GND 6 DSR -+ +--- 4 DTR 8... (0 Replies)
Discussion started by: waterbear
0 Replies

6. Solaris

help me!!!! how configure modem dial up with smc in solaris 10

Dear All, i have problem during install modem dial up with smc in solaris 10. i can't find "login" because it's stop in _receive started transmit started. thanks for your attention. this is the list during i dial to this number : altconn called Device Type ACU wanted... (0 Replies)
Discussion started by: mr.ridho
0 Replies

7. IP Networking

modem detection

How to get information that where is my modem configured in /dev. I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies

8. UNIX for Advanced & Expert Users

Modem (dial up) connecton to Unix machine

Hello to all, I have one problem and hope you'll be able to help me. It's about connecting Windows PC machine to Unix machine via dial up through Hyper terminal. Connection was working in the past. In the meantime, windows machine is replaced (win XP) and unix machine stayed as is. So nothing is... (1 Reply)
Discussion started by: Mick
1 Replies

9. BSD

Carrier Detection in FreeBSD

Regarding carrier detection on FreeBSD 9.1 being run within Virtual Box: I used a usb-serial dongle which shows up as ttyu0 on the BSD machine. Carrier detection appears to work. When I establish a null modem connection I receive a login prompt. If I login, and then unplug and plug back the... (2 Replies)
Discussion started by: rstor
2 Replies
MojoMojo::Formatter::WikipediaLink(3pm) 		User Contributed Perl Documentation		   MojoMojo::Formatter::WikipediaLink(3pm)

NAME
MojoMojo::Formatter::WikipediaLink - Linked Wikipedia by writing {{wikipedia:<lang> <word>}} DESCRIPTION
Normally, to hyperlink to the Wikipedia, you'd write: [wikipedia Hello](http://en.wikipedia.org/wiki/Hello) This plugin lets you write just {{wikipedia Hello}} not just Link to Wikipedia in English page, you can use many languages {{wikipedia:ja a~XXa~XXa~XXa~XXa~XX}} {{wikipedia:fr Salut}} Actually, if you wrote this without a language ex.{{wikipedia Foo}}, select location of Wikipedia Link is getting default-language setting of MojoMojo. METHODS
format_content_order The WikipediaLink formatter has no special requirements in terms of the order it gets run in, so it has a priority of 17. format_content Calls the formatter. Takes a ref to the content as well as the context object. process Here the actual formatting is done. SEE ALSO
MojoMojo and Module::Pluggable::Ordered. AUTHORS
Dai Okabayashi, "bayashi at cpan . org" LICENSE
This library is free software. You can redistribute it and/or modify it under the same terms as Perl itself. perl v5.14.2 2010-05-23 MojoMojo::Formatter::WikipediaLink(3pm)
All times are GMT -4. The time now is 07:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy