06-10-2013
Thanks.
You are right. It was selected SMS.
Last edited by bakunin; 06-10-2013 at 08:20 PM..
9 More Discussions You Might Find Interesting
1. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
2. Shell Programming and Scripting
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
3. Programming
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
4. Solaris
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (2 Replies)
Discussion started by: rgilan01
2 Replies
5. UNIX for Advanced & Expert Users
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (1 Reply)
Discussion started by: rgilan01
1 Replies
6. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
7. Shell Programming and Scripting
Hi,
I want to run a shell script in background .
but its going to stopped state
$ ksh cat_Duplicate_Records_Removal.ksh &
8975
$
+ Stopped (tty output) ksh cat_Duplicate_Records_Removal.ksh &
why is this happening?
Also could anyone please tell me what is a stopped... (12 Replies)
Discussion started by: TomG
12 Replies
8. BSD
Hi Experts,
I am facing one problem here which is one process always stuck in running state which causes the other similar process to sleep state . This causes my system in hanged state.
On doing cat /proc/<pid>wchan showing the "__init_begin" in the output.
Can you please help me here... (0 Replies)
Discussion started by: naveeng
0 Replies
9. UNIX for Advanced & Expert Users
Hi Experts,
I am facing one problem here which is one process always stuck in running state which causes the other similar process to sleep state . This causes my system in hanged state.
On doing cat /proc/<pid>wchan showing the "__init_begin" in the output.
Can you please help me here... (1 Reply)
Discussion started by: naveeng
1 Replies
LEARN ABOUT HPUX
vparutil
vparutil(1M) vparutil(1M)
NAME
vparutil - get and set SCSI parameters for SCSI controllers from a virtual partition
SYNOPSIS
dev_path
dev_path
dev_path scsi_id] scsi_rate]
DESCRIPTION
The command gets and sets SCSI parameters for SCSI controllers within a running virtual partition. When setting the SCSI parameters using
the option, the virtual partition which owns the specified SCSI controller must be in the down state. If not, the command will fail with
the appropriate error code.
The SCSI parameters for a given SCSI controller must first be set (from the firmware BCH prompt or using the option) before the parameters
can be retrieved using the option.
The command is allowed on Itanium(R)-based platforms for compatibility. No action is taken for the command.
Options
recognizes the following command-line options:
Deletes an entry for the specified SCSI controller at
dev_path from the SCSI table.
Gets the SCSI parameters for the specified SCSI controller at
dev_path.
Sets the SCSI parameters for the specified SCSI controller at
dev_path.
Operands
recognizes the following command-line operands:
dev_path The device path of the SCSI controller.
id The SCSI ID for the specified controller (defaults to 7).
rate The SCSI rate for the specified controller. This parameter can have one of two values: for the corresponding fast wide and
ultra wide SCSI interfaces.
Note
For managing SCSI controllers, use corresponding SCSI utilities. For further information refer to
SECURITY RESTRICTIONS
This command is restricted to processes owned by superuser.
When virtual partition flexible administrative capability is enabled, only a Designated-Admin vPar can set SCSI parameters for SCSI con-
trollers.
EXAMPLES
Set the SCSI ID for controller at 0/0/2/0 to 3 with the fast wide rate:
RETURN VALUE
Successful.
Invalid SCSI controller specification.
Invalid SCSI ID.
Could not communicate with virtual partition monitor.
Virtual partition which owns SCSI controller is not in down state.
Internal firmware call failed.
Other error.
AUTHOR
was developed by the Hewlett-Packard Company.
SEE ALSO
vparadmin(1M), vparboot(1M), vparcreate(1M), vparconfig(1M), vpardump(1M), vparefiutil(1M), vparenv(1M), vparextract(1M), vparmodify(1M),
vparreloc(1M), vparremove(1M), vparreset(1M), vparstatus(1M), vparresources(5), vpartition(5), vpmon(5).
vparutil(1M)