metahs(1M)						  System Administration Commands						metahs(1M)

NAME

       metahs - manage hot spares and hot spare pools

SYNOPSIS

       /usr/sbin/metahs [-s setname] -a all component

       /usr/sbin/metahs [-s setname] -a hot_spare_pool [component]

       /usr/sbin/metahs [-s setname] -d hot_spare_pool [component]

       /usr/sbin/metahs [-s setname] -d all component

       /usr/sbin/metahs [-s setname] -e component

       /usr/sbin/metahs [-s setname] -r hot_spare_pool component-old

       /usr/sbin/metahs [-s setname] -r all component-old component-new

       /usr/sbin/metahs [-s setname] -i [hot_spare_pool...]

DESCRIPTION

       The  metahs  command manages existing hot spares and hot spare pools. It is used to add, delete, enable, and replace components (slices) in
       hot spare pools. Like the metainit command, the metahs command can also create an initial hot spare  pool.  The	metahs	command  does  not
       replace a component of a metadevice. This function is performed by the metareplace command.

       Hot  spares are always in one of three states: available, in-use, or broken. Available hot spares are running and ready to accept data, but
       are not currently being written to or read from. In-use hot spares are currently being written to and read from. Broken hot spares are  out
       of service and should be repaired. The status of hot spares is displayed when metahs is invoked with the -i option.

       Solaris	Volume Manager supports storage devices and logical volumes, including hot spares, greater than 1 terabyte (TB) when Solaris 10 is
       running a 64-bit kernel.

       If a system with large volumes or hot spares is rebooted under a 32-bit Solaris 10 kernel, the large volumes are visible  through  metastat
       output,	but  they cannot be accessed, modified or deleted, and no new large volumes can be created. Any volumes or file systems on a large
       volume in this situation are also unavailable. If a system with large volumes is rebooted under a version of Solaris prior to  Solaris  10,
       Solaris	Volume	Manager  will not start. All large volumes must be removed before Solaris Volume Manager runs under another version of the
       Solaris Operating Environment.

OPTIONS

       Root privileges are required for any of the following options except -i.

       The following options are supported:

       -a all  component

	   Add component to all hot spare pools. all is not case sensitive.

       -a hot_spare_pool [component]

	   Add the component to the specified hot_spare_pool. hot_spare_pool is created if it does not already exist.

       -d all  component

	   Delete component from all the hot spare pools. The component cannot be deleted if it is in the in-use state.

       -d hot_spare_pool [component]

	   Delete hot_spare_pool, if the hot_spare_pool is both empty and not referenced by a metadevice. If component is specified, it is deleted
	   from the hot_spare_pool. Hot spares in the in-use state cannot be deleted.

       -e component

	   Enable  component  to  be  available  for  use  as  a hot spare. The component can be enabled if it is in the broken state and has been
	   repaired.

       -i [hot_spare_pool...]

	   Display the status of the specified hot_spare_pool or for all hot spare pools if one is not specified.

       -r all component-old component-new

	   Replace component-old with component-new in all hot spare pools which have the component associated. Components cannot be replaced from
	   any hot spare pool if the old hot spare is in the in-use state.

       -r hot_spare_pool component-old component-new

	   Replace  component-old  with  component-new in the specified hot_spare_pool. Components cannot be replaced from a hot spare pool if the
	   old hot spare is in the in-use state.

       -s setname

	   Specify the name of the diskset on which metahs works. Using the -s option causes the command to perform  its  administrative  function
	   within the specified diskset. Without this option, the command performs its function on local hot spare pools.

OPERANDS

       The following operands are supported:

       component	       The logical name for the physical slice (partition) on a disk drive, such as /dev/dsk/c0t0d0s2.

       hot_spare_pool	       Hot spare pools must be of the form hspnnn, where nnn is a number in the range 000-999.

EXAMPLES

       Example 1: Adding a Hot Spare to a Hot Spare Pool

       The following example adds a hot spare /dev/dsk/c0t0d0s7 to a hot spare pool hsp003:

       # metahs -a hsp003 c0t0d0s7

       When  the hot spare is added to the pool, the existing order of the hot spares already in the pool is preserved. The new hot spare is added
       at the end of the list of hot spares in the hot spare pool specified.

       Example 2:  Adding a Hot Spare to All Currently Defined Pools

       This example adds a hot spare to the hot spare pools that are currently defined:

       # metahs -a all c0t0d0s7

       The keyword all in this example specifies adding the hot spare, /dev/dsk/c0t0d0s7, to all the hot spare pools.

       Example 3:  Deleting a Hot Spare

       This example deletes a hot spare, /dev/dsk/c0t0d0s7, from a hot spare pool, hsp003:

       # metahs -d hsp003 c0t0d0s7

       When you delete a hot spare, the position of the remaining hot spares in the pool changes to reflect the new order.  For  instance,  if	in
       this example /dev/dsk/c0t0d0s7 were the second of three hot spares, after deletion the third hot spare would move to the second position.

       Example 4: Replacing a Hot Spare

       This example replaces a hot spare that was previously defined:

       # metahs -r hsp001 c0t1d0s0 c0t3d0s0

       In this example, the hot spare /dev/dsk/c0t1d0s0 is replaced by /dev/dsk/c0t3d0s0. The order of the hot spares does not change.

EXIT STATUS

       The following exit values are returned:

       0	Successful completion.

       >0	An error occurred.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWmdu			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       mdmonitord(1M),	metaclear(1M),	metadb(1M), metadetach(1M), metainit(1M), metaoffline(1M), metaonline(1M), metaparam(1M), metarecover(1M),
       metarename(1M), metareplace(1M), metaroot(1M), metaset(1M), metassist(1M), metastat(1M), metasync(1M), metattach(1M), md.tab(4),  md.cf(4),
       mddb.cf(4), md.tab(4), attributes(5), md(7D)

       Solaris Volume Manager Administration Guide

WARNINGS

       Do  not	create large (>1 TB) volumes if you expect to run the Solaris Operating Environment with a 32-bit kernel or if you expect to use a
       version of the Solaris Operating Environment prior to Solaris 10.

SunOS 5.10							    8 Aug 2003								metahs(1M)