06-10-2013
Personally I've never seen a Solaris install routine set up a mirror all on its own. Okay, I guess you learn something new every day!!!
However, the metastat output confirms that is what it's done so, as you say, you can break the mirror and remake the mirror with a different drive using the tools. Give it a go.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello all,
How does the Solaris identifies the controller subscript ? ( like c0txdxs0 or c1txdxsx ?? )
I have a unix box ( Ultra 30) running with 2.5.1.
When I connected an external hard disk to the on-board scsi port, it got identified as c0t1dxsx...
(... (1 Reply)
Discussion started by: shibz
1 Replies
2. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
3. Solaris
Dear Solarizer,
If i have a disk let say like this c1t0d0s0
How to change the controller to be come example : c3t0d0s0
Thanxs For your replay
Regads,
tpx (3 Replies)
Discussion started by: tpx99
3 Replies
4. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
5. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT DEBIAN
simple-cdd
SIMPLE-CDD(1) General Commands Manual SIMPLE-CDD(1)
NAME
simple-cdd - create custom debian-installer CDs
SYNOPSIS
simple-cdd [options]
OPTIONS
--conf Specify a configuration file
--dist Specify a distribution (etch, lenny, sid)
--graphical-installer|-g
Enable graphical installer by default
--serial-console|-s
Set defaults for serial console
--do-mirror
Generate a local mirror
--no-do-mirror
Do not generate a local mirror
--profiles|-p
Select profiles (Examples in /usr/share/simple-cdd/profiles/ directory)
--build-profiles|-b
Profiles only used while building the CD
--auto-profiles|-a
Pre-select and automatically install these profiles
--local-packages
List of packages to be included on CD's local package repository
--locale
Select locale (language and country)
--keyboard
Select keyboard (console-keymaps-at/keymap debconf question)
--debian-mirror
Specify debian mirror (The default is: ftp://ftp.us.debian.org/debian)
--security-mirror
Specify securty mirror (The default is: http://security.debian.org/)
--mirror-tools
List the mirror tools to be used (The defaults are both wget and reprepro)
--kernel-packages
List of kernel packages to be included on the CD
--help|-h
Display the usage message
--qemu|-q
Use qemu to test the built image
--force-preseed
Only issue a warning if a preseeding file is invalid
--profiles-udeb-dist
Specify distribution to pull simple-cdd-profiles udeb from
--extra-udeb-dist
Specify additional distribution to pull udebs from
EXAMPLES
simple-cdd --profiles x-basic -g
Build a custom image using the default options, except for using the graphical installer by default and the x-basic profile
(/usr/share/simple-cdd/x-basic.*)
AUTHOR
This manual page was written by Gustavo Franco <stratus@acm.org>, for the Debian project (but may be used for others).
Oct 28th, 2007 SIMPLE-CDD(1)