06-08-2013
Is raidctl works on that platform?
If yes, then it could be helpful too.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello all,
How does the Solaris identifies the controller subscript ? ( like c0txdxs0 or c1txdxsx ?? )
I have a unix box ( Ultra 30) running with 2.5.1.
When I connected an external hard disk to the on-board scsi port, it got identified as c0t1dxsx...
(... (1 Reply)
Discussion started by: shibz
1 Replies
2. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
3. Solaris
Dear Solarizer,
If i have a disk let say like this c1t0d0s0
How to change the controller to be come example : c3t0d0s0
Thanxs For your replay
Regads,
tpx (3 Replies)
Discussion started by: tpx99
3 Replies
4. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
5. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies