Hello all,
How does the Solaris identifies the controller subscript ? ( like c0txdxs0 or c1txdxsx ?? )
I have a unix box ( Ultra 30) running with 2.5.1.
When I connected an external hard disk to the on-board scsi port, it got identified as c0t1dxsx...
(... (1 Reply)
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Dear Solarizer,
If i have a disk let say like this c1t0d0s0
How to change the controller to be come example : c3t0d0s0
Thanxs For your replay
Regads,
tpx (3 Replies)
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT OSX
locale::codes::langfam
Locale::Codes::LangFam(3pm) Perl Programmers Reference Guide Locale::Codes::LangFam(3pm)NAME
Locale::Codes::LangFam - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangFam;
$lext = code2langfam('apa'); # $lext gets 'Apache languages'
$code = langfam2code('Apache languages'); # $code gets 'apa'
@codes = all_langfam_codes();
@names = all_langfam_names();
DESCRIPTION
The "Locale::Codes::LangFam" module provides access to standard codes used for identifying language families, such as those as defined in
ISO 639-5.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 639-5
language family codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language families. A code set may be specified using either a name, or a
constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langfam('apa','alpha');
$lext = code2langfam('apa',LOCALE_LANGFAM_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from ISO 639-5 such as 'apa' for Apache languages.
This is the default code set.
ROUTINES
code2langfam ( CODE [,CODESET] )
langfam2code ( NAME [,CODESET] )
langfam_code2code ( CODE ,CODESET ,CODESET2 )
all_langfam_codes ( [CODESET] )
all_langfam_names ( [CODESET] )
Locale::Codes::LangFam::rename_langfam ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangFam::add_langfam ( CODE ,NAME [,CODESET] )
Locale::Codes::LangFam::delete_langfam ( CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_alias ( NAME ,NEW_NAME )
Locale::Codes::LangFam::delete_langfam_alias ( NAME )
Locale::Codes::LangFam::rename_langfam_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::delete_langfam_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.loc.gov/standards/iso639-5/id.php
ISO 639-5 .
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2012 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.2 2012-10-11 Locale::Codes::LangFam(3pm)