06-07-2013
I'm not at all sure that I understand what you are trying to do having re-read your post twenty times.
Why do you care what order the drives are?
Is this the scenario? You installed a server and then decided that the disk drives needed changing for some reason? You put a completely new set of drives in the server and restored the original installation from backup but it won't run???? Is that it?
Also, what are the filesystems? ufs, zfs or what?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello all,
How does the Solaris identifies the controller subscript ? ( like c0txdxs0 or c1txdxsx ?? )
I have a unix box ( Ultra 30) running with 2.5.1.
When I connected an external hard disk to the on-board scsi port, it got identified as c0t1dxsx...
(... (1 Reply)
Discussion started by: shibz
1 Replies
2. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
3. Solaris
Dear Solarizer,
If i have a disk let say like this c1t0d0s0
How to change the controller to be come example : c3t0d0s0
Thanxs For your replay
Regads,
tpx (3 Replies)
Discussion started by: tpx99
3 Replies
4. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
5. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
SBP(4) BSD Kernel Interfaces Manual SBP(4)
NAME
sbp -- Serial Bus Protocol 2 (SBP-2) Mass Storage Devices driver
SYNOPSIS
kldload firewire
kldload cam
kldload sbp
or
device sbp
device firewire
device scbus
device da
device cd
device pass
DESCRIPTION
The sbp driver provides support for SBP-2 devices that attach to the FireWire (IEEE 1394) port. It should work with SBP-2 devices which the
CAM layer supports, for example, HDDs, CDROM drives and DVD drives.
Some users familiar with umass(4) might wonder why the device is not detached at the CAM layer when the device is unplugged. It is detached
only if the device has not been plugged again during several bus resets. This is for preventing to detach an active file system even when
the device cannot be probed correctly for some reason after a bus reset or when the device is temporary disconnected because the user changes
the bus topology. If you want to force to detach the device, run ``fwcontrol -r'' several times or set hw.firewire.hold_count=0 by
sysctl(1).
Some (broken) HDDs do not work well with tagged queuing. If you have problems with such drives, try ``camcontrol [device id] tags -N 1'' to
disable tagged queuing.
SEE ALSO
cam(4), firewire(4), camcontrol(8), fwcontrol(8), kldload(8), sysctl(8)
AUTHORS
The sbp driver was written by Katsushi Kobayashi and Hidetoshi Shimokawa.
This manual page was written by Katsushi Kobayashi.
BSD
May 20, 2002 BSD