Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: POST displays error sparc netra 240
Special Forums Hardware POST displays error sparc netra 240 Post 302811775 by SunSolars_admin on Friday 24th of May 2013 06:36:38 AM
Old 05-24-2013
Sun
Please get a new DIMM and fix. Run the diagnostics (Extended level) and once completed. Bring down the server and make it up and check if its shows full required Memory size..


If this doesnt work, you need replace a New tested Motherboard with RAM
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

help on ksh and sql..getting error as is too long. maximum size is 240 characters."

Hi, In my script i am executing sql file and there are some variables in SQL files which are assigned at run time. one of the variable value is having more than 240 characters and at time of execution its getting failed with error as "is too long. maximum size is 240 characters." ... (1 Reply)
Discussion started by: pooga17
1 Replies

2. Solaris

Netra 240 Hard disk are not detected

Hi All, I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine. Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies

3. Solaris

Netra V440 & Netra 1290 keyswitch

Hello, I wrote a script which monitor the keyswitch state repeatedly each 10 minutes. I'm extracting the keyswitch status by using prtdiag. The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status. unlike Netra 440 server , I found that... (2 Replies)
Discussion started by: Alalush
2 Replies

4. Solaris

new sparc netra 500mhz problem

hey guys i'm in university and i bought my self a sun ultra SPARC netra 500mhz machine with the usb ports a vga gfc and cdrom drive now i have a problem (bought it off ebay) i trying to install a fresh solaris 10 server op onto it but it looks like it previously had linix installed and... (38 Replies)
Discussion started by: garethmob
38 Replies

5. Solaris

Sun Netra T1 won't poweron/no POST

Hi guys. I have an old Netra T1 that I'm hoping to recover here so I can twiddle around with Solaris 10. It's been unable to power on despite issuing the "poweron" command or hitting the switch at the back of the server for some time. The LOM command "env" reports ALARM3 ON and everything else... (8 Replies)
Discussion started by: detach8
8 Replies

6. Solaris

netra 240 difference

Hi, sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server? can anyone tell the difference. RJS (1 Reply)
Discussion started by: rajasekg
1 Replies

7. UNIX for Dummies Questions & Answers

Refurbished Netra 240 servers hangs after POST test

Hello everyone, I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately. At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a... (0 Replies)
Discussion started by: afferbwt
0 Replies

8. Solaris

SUN Netra 240 Boot error

Hi, When I am trying to boot my SUN Netra 240 Machine its giving some boot error. > {1} ok boot -i > Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i > Boot load failed. > The file just loaded does not appear to be executable. > {1} ok I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies

9. Solaris

Unable to access serial port from non-global solaris zone on netra 240

I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Discussion started by: disagreeable
0 Replies

10. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies

LEARN ABOUT NETBSD

finsio

FINSIO(4)						   BSD Kernel Interfaces Manual 						 FINSIO(4)

NAME

     finsio -- Fintek LPC Super I/O driver

SYNOPSIS

     finsio0 at isa? port 0x4e

DESCRIPTION

     The finsio driver provides support for the Fintek F71805F, F71806F, F71862FG, F71872, F71882 and F71883 LPC Super I/O chips.

     Only the Hardware Monitor device is supported and it provides you to monitor the sensors through the envsys(4) API.

     The finsio Super I/O Hardware Monitor supports 15 sensors (this depends on the chip ID):

	   Sensor    Units    Typical Use
	   IN0	     uV DC    Internal 3.3Vcc
	   IN1	     uV DC    Memory Vtt
	   IN2	     uV DC    RAM Vcc
	   IN3	     uV DC    Chipset V
	   IN4	     uV DC    +5V
	   IN5	     uV DC    +12V
	   IN6	     uV DC    Vcc 1.5V
	   IN7	     uV DC    Vcore
	   IN8	     uV DC    Vsb
	   IN9	     uV DC    Vbat (optional)
	   Temp1     uK       CPU Temperature
	   Temp2     uK       Motherboard Temperature
	   Temp3     uK       (undefined)
	   Fan0      RPM      CPU Fan
	   Fan1      RPM      User Fan1
	   Fan2      RPM      User Fan2

SEE ALSO

     envsys(4), envstat(8)

HISTORY

     The finsio driver first appeared in NetBSD 5.0.

AUTHORS

     The finsio driver was written by Geoff Steckel and Juan Romero Pardines.

BSD
								   April 3, 2008							       BSD
All times are GMT -4. The time now is 01:17 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy