What is the command to count lines in a files, but ignore blank lines and commented lines?
I have a file with 4 sections in it, and I want each section to be counted, not including the blank lines and comments... and then totalled at the end.
Here is an example of what I would like my... (6 Replies)
I have a data file in the following format (refer to input file) with multiple lines containing some information. I need an output file to loop thorough the input file with summarized information as seen below (refer to output file) ‘Date Time' and ‘Beta Id' input file values should be concatenated... (7 Replies)
Please help in the following problem:
Input is:
Pritam
123
456
Patil
myname
youname
Pritam
myproject
thisproject
iclic
Patil
remaining text
some more text
I need the command which will display the no of lines between two words in the whole file.
e.g. Display all the no of lines... (5 Replies)
Hi!
I have a file that looks like this:
AAG
----------------------------------------------------------------------
Number of residues in the repeat = 3
AGA
----------------------------------------------------------------------
Number of residues in the repeat = 3
AGG
... (2 Replies)
Hi,
I had posted few days back and got replies on how to extract patterns from a file.
I had another question. I want to count the number of lines a particular pattern. I thought of somethings like using NF variable, etc, but they didnt work.
Here is sample input.
... (9 Replies)
I have a file that I need to merge with another like file. Normally I remove the trailer reocrd and merge the file and update the trailer record of the second file. I did a WC -l on the first file before I removed the trailer record, and again afterwards. The count came back the same. I opened the... (6 Replies)
I try to count number of lines of a data.txt file and then if number of lines is greater than 1 then email me the file.
I could not find what is wrong with my code, hope you can point out the mistake i made
#! /bin/ksh
count =`cat /from/file/data.txt | wc -l`
if ]; then
mailx -s... (4 Replies)
I have 2 files, and I want to count how many lines contain matching words.
Example:
file1
a_+b
a_+b_+c
file2
ab a_+b
a_+bc
I want to get 1, as the the first line of file1 is a substring of the first line of file2. While the second line isn't.
I suspect using sdiff, but not sure how to... (3 Replies)
Hi all,
I have my script to execute number of commands (command line interface) using TCL.
the execution and response of the commands get stored in some log file.
While the execution is going on i need only the time of execution and the number of line getting executed to be displayed in... (1 Reply)
I am tiring to cont numbers of line between the "!" in CISCO routers
I have no problem to extract the input and change the empty line with !
!
5 Cable5/0/1 U0 4
5 Cable5/0/1 U1 4
!
5 Cable5/0/1 U2 4 ... (4 Replies)
Discussion started by: sharong
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)