Sponsored Content
Special Forums Hardware How to remove fan from cpu fan chassis? Post 302808779 by Corona688 on Friday 17th of May 2013 01:34:24 PM
Old 05-17-2013
A narrow screwdriver may be able to reach through the fan blades to the screws.

They would be beneath the blades, not beneath the central hub... Look for sort of plastic tabs.

Last edited by Corona688; 05-17-2013 at 03:06 PM..
 

7 More Discussions You Might Find Interesting

1. BSD

Fan control

Hi all, Is there any way that I can get some control over th fan in my Evo N400C laptop running OpenBSD 4.0? Right now the fan is running constantly and it woulf be nice if it could be quiet sometime. (1 Reply)
Discussion started by: Timmy66
1 Replies

2. Hardware

Fan Tray for Sunfire T2000

Recently the rear fan assembly of one of our T2000 servers went faulty. I could replace it immediately with the one from a currently powered off standby machine. But now this one has to be replaced. So I got a quote from our supplier who charges EUR 776 for a new spare part or EUR 405 (all... (0 Replies)
Discussion started by: hergp
0 Replies

3. What is on Your Mind?

I just ordered a Mini-Box with no fan!

I just ordered a Mini-Box M350 with a Mini-ITX Intel DM510MO motherboard. NO FAN! I've come to hate the wine of spinning mechanisms in PCs in my quiet home. This one is for surfing the web in my living room (instead of using this laptop), so it doesn't really need much power. If I do... (1 Reply)
Discussion started by: KenJackson
1 Replies

4. Solaris

Fan failure

would Solaris 10 shutdown automatically if both CPU fans fail? (7 Replies)
Discussion started by: orange47
7 Replies

5. Hardware

How to replace the fan in the HP J6000?

Hi all, it is me again..now my HP J6000 fan is spoilt. Based on the error, i suspected it is Fan 1 in the power supply, however there is 3 fans in the power supply, how do i know which is Fan 1? Thanks for your response regards (2 Replies)
Discussion started by: lchunleo
2 Replies

6. Solaris

Sun Fire V210 CPU Fan Temp too high?

Hey, I have a V210 with a failed CPU fan. The temperature is currently at 84C and I've been asked to wait a few weeks before replacing as its a production system and it cant be shut down yet. Is it too hot? Do I risk killing the CPU at this temp? Its been like this for a few weeks now... (5 Replies)
Discussion started by: magarvo
5 Replies

7. Solaris

Sun v215 Fan Speed

Hi all, I made some calculations and it seems that fans are working more than they supposed to keep the internals at the specified values. Is there a way to adjust this ? I have 2 approaches ; -from ALOM sc|ok prompt -from Solaris 10 or -from a HW Switch I am pretty sure that... (5 Replies)
Discussion started by: y33t
5 Replies
CREATE_MAKEFILE 						  [FIXME: manual]						   CREATE_MAKEFILE

NAME
create_makefile - Creates Makefile.in and Makefile from a Makefile.am SYNOPSIS
create_makefile [relativepath/Makefile] [relativepath] DESCRIPTION
create_makefile creates the Makefile.in and Makefile in a subdirectory containing a Makefile.am. This script saves time compared to re-running configure completely Note that you must supply the path to the desired MakefileMakefile.am (though the final /Makefile may be omitted). This script may be run from the toplevel directory (the one containing configure) or from one of it's subdirectories. If the source directory is different from the build directory (see the environment variables below), it will be assumed that the Makefile.am and Makefile.in belong beneath the source directory and that the Makefile belongs beneath the build directory. This utility is part of the KDE Software Development Kit. ENVIRONMENT
One of the following variables (but not both) should be set if the source directory is different from the build directory. If the build directory is simply a subdirectory of the source directory, the simpler variable OBJ_SUBDIR should be used. OBJ_SUBJDIR Indicates that the build directory is in the given subdirectory of the source directory. For instance, if the source directory is kdesdk and the build directory is kdesdk/obj-i386-linux, then OBJ_SUBDIR should be set to obj-i386-linux. OBJ_REPLACEMENT A sed expression that is used to transform the source directory into the build directory. For instance, if the source directory is ~/src/kdesdk and the build directory is ~/src/kdesdk-obj, then OBJ_REPLACEMENT should be set to s#kdesdk#kdesdk-obj#. SEE ALSO
create_makefiles(1) AUTHORS
create_makefile was written by David Faure<faure@kde.org> and others. This manual page was prepared by Ben Burton<bab@debian.org> for the Debian GNU/Linux system (but may be used by others). [FIXME: source] March 8, 2003 CREATE_MAKEFILE
All times are GMT -4. The time now is 06:23 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy