05-16-2013
There's no generic CD to USB converter... They're just not the same thing. Making it boot on USB is more akin to making it boot from a hard drive.
An external USB cdrom is a good tool to have for cases like this.
9 More Discussions You Might Find Interesting
1. Windows & DOS: Issues & Discussions
hello again all,
assume I can not log in to the windows installation, (maybe) because of a system file corruption or failure.. however, I do log in to the system using the windows CD with R (repair) mode, that is the command line prompt.
Is there a way in that command prompt to copy the files... (10 Replies)
Discussion started by: milhan
10 Replies
2. Linux
What are the differences, advantages, and disadvantages? (1 Reply)
Discussion started by: Advice Pro
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I am new to this forum. Can anyone help me to find a unix editor/software which will work in windows. Thanks (6 Replies)
Discussion started by: sundaresanv
6 Replies
4. UNIX for Dummies Questions & Answers
Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive.
Thanks! (4 Replies)
Discussion started by: Xterra
4 Replies
5. Ubuntu
I am trying to dual boot on an external USB 500GB drive using my laptop.I have Windows 7 installed and booting on 1st partition 230GB now as active primary, 2nd partition is 100GB as primary, and 3rd partition is 135GB as primary. I was intending on installing Ubuntu onto the 2nd partition. I read... (12 Replies)
Discussion started by: coolecho
12 Replies
6. Boot Loaders
I successfully created a bootable windows 7 repair usb.
Please clarify me:
I rebooted my system via USB. windows repair window appeared. There were 5 options. I opted 'windows memory diagnostic' and it worked fine. There was an option named 'start up repair'. This option can be used if windows... (2 Replies)
Discussion started by: ravisingh
2 Replies
7. Boot Loaders
I need to make a bootable usb of windows 7 repair disc iso file so that I can use it in case my system doesn't boot up. On net I am getting complete windows 7 OS iso but I need only the repair disc for making bootable iso. I am not sure whether I used right word by using the word disc here... (3 Replies)
Discussion started by: ravisingh
3 Replies
8. Windows & DOS: Issues & Discussions
I have a 1TB HD, suspect it had bad sectors and blocks...
it was pre-installed with windows 8.0..
I was able to boot up ubuntu and looked at the partitions and run a badblocks comand to verify secotors, after getting a serious of Input and Output errors mounting the partition and doing any... (2 Replies)
Discussion started by: ppchu99
2 Replies
9. HP-UX
Greetings.
Seeking guidance on adding a USB barcode reader (BCR) to an HP c3750 workstation with HP-UX 11.11 which is essentially configuring X windows to accept input from both a primary keyboard and a secondary keyboard that happens to be the BCR.
Historically, I have successfully added a BCR... (2 Replies)
Discussion started by: mnkaltenbach
2 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD