The problem is that "restore"/"backup" file format has no "table of contents", so basically "restore" has to read the whole file to generate it. The limiting factor is the speed of the tape (this is probably the case with the "backup" too).
What you can do is: instead of piping the file list directly into "backup" create a file first. Then write this file first at the rmt-device, only then use the same list as input to "backup". Write to the "/dev/rmtN.1" instead of "/dev/rmtN", this is the drive without "rewind on exit", so your "table of contents" will be the first entry on the cartridge. You can restore this single file to get/search a list of files backed up in this session.
Backup (schematic)
Search (=restore toc only)
Restore (schematic, skip first entry, then restore normally)
I hope this helps.
HI All
I have created the bootable recovery tape using the ignite command make_tape_recovery, I need help for the command to list the content recorded in that tape.
Regards,
Gege:confused: (1 Reply)
I'm pulling a 1MB file from tape using tar. It's a 300GB DLT tape and it does have a lot of files on it because it's go the entire OS and Oracle RMAN files and 3000 table exports, but it's taking 2-3 hours to pull this file off of it. Is this type of performance what I should expect?
The... (0 Replies)
Hello guys,
I am having a requirement,
I am having three file m1,m2,m3 having some contents. I want to list last 20 lines of m1,m2 and m3 all together on the terminal.
I used tail -20 m1 m2 m3,
but it is showing error,
tail: option used in invalid context -- 2
Can u help me... (2 Replies)
Hi fellows,
Can you please share any command with which I can list down the file names inside a tar.gz file.
I have tried with these possibilities but in vain.
bash-3.00$ tar -ztvf file.tar.gz
tar: z: unknown function modifier
bash-3.00$ tar ztvf file.tar.gz
tar: z: unknown function... (1 Reply)
had this p520 server connected to a DDS-3 4mm tape drive...
running AIX 7.1 TL01 -- the latest release.
mksysb -i -e /dev/rmt/1 ..tells me only 1% is done after over an hour ...
I had no problems with th hardware and other connections...
tar command to /dev/rmt/1 runs very fast ....... (3 Replies)
Hi.
I have this old server onto which i needed to list the content of a tape. This is a SCO box (SCO_SV 3.2 5.0.6 i386) and backup was done using cpio.
#tape status
status : ready beginning-of-tape
soft errors : 0
hard errors : 0
underruns : 0
#dtype /dev/rct0
/dev/rct0 ... (5 Replies)
Hi,
We replaced one of our tape drives (attached to a SPARC Server) with an LTO5 one (external, attached vi SAS). Manually we check (using tar) that the OS can write data to the Tape Drive, however, the application backup is failing.
Since the application takes its own backup, the apps team... (0 Replies)
Hi All,
I would like to know couple of ways to list the content available in tar and gzipped file without extracting.
i.e., I would like to display the contents of test.tar.gz without extracting.
Note :: please suggest a command other that tar -ztvf (9 Replies)
I am often given log files at work in .csv format to work with, normally extracting various fields. I then have to figure out the number of each field so that I can extract that field with cut or awk. Normally I just manually count the fields, based on the field separator. I would like to be... (3 Replies)
Hi All
I have a file which contains the timestamp of the log and a message and I want to implement a polling mechanism, where this log file is pooled every 2 minutes and list the errors in the file. I want to list down the errors only after the timestamp in the file is more than the current... (2 Replies)
Discussion started by: infyanurag
2 Replies
LEARN ABOUT DEBIAN
partclone.restore
partclone.restore(8) System Manager's Manual partclone.restore(8)NAME
partclone.restore - The utility to restore an etx2/ext3 partition.
SYNOPSIS
partclone.restore [options]... [MODE] [SOURCE FILE] [OUTPUT FILE]
DESCRIPTION
partclone.restore is a part of Partclone project. Partclone is a project like the well-known backup utility "Partition Image" a.k.a par-
timage. Partclone provide utilities to back up used blocks and design for higher compatibility of the file system using supported library
like e2fslibs.
OPTIONS -o, --output FILE
Output FILE
-O --overwrite FILE Output FILE, overwriting if exists
--restore_row_file create special raw file for loop device
-s, --source FILE
Source FILE
-L, --logfile FILE
Log FILE
-dX, --debug=X
Set the debug level to X = [0|1|2]
-C, --no_check
Don't check device size and free space
-X, --dialog
Output message as Dialog Format
-I, --ignore_fschk
Ignore filesystem check
--ignore_crc
Ignore crc check error
-F, --force
Force progress
-f, --UI-fresh
Fresh times of progress
-m, --max_block_cache
The used block will be cache until max number
-q, --quiet
Disable progress message
-v, --version
Display partclone version
-h, --help
Display this help
Examples:
restore /dev/hda1 from hda1.img and display debug information.
partclone.restore -d -s hda1.img -o /dev/hda1
restore image from clonezilla(split, gzip,) with stdin source
cat sda1.ext3-ptcl-img.gz.a* > gunzip -c | partclone.restore -d -s - -o /dev/sda1
restore raw image from partclone.dd
partclone.dd -d -c -s /dev/sda1 -o - | partclone.restore -d -s - -o /dev/sdb1
REPORTING BUGS
Report bugs to <thomas@nchc.org.tw>
SUPPORT
You can get support at http://partclone.org
AUTHOR
This manual page was written by Thomas Tsai <thomas@nchc.org.tw>
partclone 0.2.48 Nov 2007 partclone.restore(8)