Not the problem here, but
would be more efficient.
And the following ensures it matches the whole line:
Back to the problem:
Mr. Scru made suggestion to find the root cause!
Solaris sed needs a space here:
Please share the output of the following:
Hi All,
Can anyone explain me the meanning of the following errors:
LABEL: SC_DISK_ERR2
IDENTIFIER: B6267342
Description
DISK OPERATION ERROR
Probable Causes
DASD DEVICE
Failure Causes
DISK DRIVE
DISK DRIVE ELECTRONICS
Recommended Actions
PERFORM PROBLEM DETERMINATION... (1 Reply)
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Hi all,
My disk space is 100% full.
df -k <dir> -> 100%
One of my debug files consume huge amount of space and i want to remove the same to start off fresh debugs.
However i'm unable to remove the file giving out the following error message:
rm -f debug.out22621
rm: cannot remove... (8 Replies)
one of my servers / was full by 100% i cleard some space, now though i have
enough space on / partition still df is showing disk usage as 100% am not able to create any single txt file ? why so ? (3 Replies)
I have a weird situation in which the binary dumps core and gives bus error. But before dumping the core and throwing the buss error, it gives some output.
unfortunately I can't grep the output before core dump
db2bfd -b test.bnd
maxSect 15
Bus Error (core dumped)
But if I do ... (4 Replies)
Hi,
I am unable to get the full FS space, as /home is 100% utilized and after deleting unwanted files, its still 100%. After checking the du -sk * | sort -n output and converting it to MBs, the total sizes comes out to be 351 MBs only however the lvol is of 3GB. I don't know where is all the space... (2 Replies)
i want to create 1 script to monitor 1 particular filesystem out of the diferent filesystems. if disk space of that particular filesystem increases by 80% it sends an alert mail to an email id
---------- Post updated at 04:18 PM ---------- Previous update was at 04:17 PM ----------
no. I am... (1 Reply)
Discussion started by: rakeshhhhhhhh
1 Replies
LEARN ABOUT HPUX
vxreattach
vxreattach(1M)vxreattach(1M)NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS -b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)