Hi
I have small home network and I want to block some forums on web
When I use this
iptables -A INPUT -s forum -j DROP
rules is applied but when I restart some of PC rules are not present any more also I tried to save firewall settings
iptables-save > /root/dsl.fw
but how to... (2 Replies)
Please i need help in how to add/remove rules in timezone files under /usr/share/zoneinfo/ , cause i have tried many times to do this by adding rules in an time zone file then compile this file with zic tool and then link it to /etc/localtime but always the output doesn't match what i have made... (0 Replies)
Hello,
I was playing around with iptables to setup an isolated system. On a SLES10 system, I ran the below to setup my first draft of rules. I noticed that the rules come into effect immediately and do not require any restart of iptables.
iptables -A INPUT -j ACCEPT
iptables -A OUTPUT -m... (4 Replies)
Hello,
I'm having problem with an iptables rule. It seems that on one of two systems on the nat table, the INPUT chain doesn't exist for some strange reason.
I get the error below:
# iptables -t nat -A INPUT -j ACCEPT
iptables: No chain/target/match by that name.
Here is my kernel on... (0 Replies)
Hi,
I am new to linux stuff. I want to use linux iptables to configure rule so that all my incoming traffic with protocol "tcp" is forwarded to the "FORWARD CHAIN". The traffic i am dealing with has destination addresss of my machine but i want to block it from coming to input chain and somehow... (0 Replies)
Could someone help me with writing rules for iptables?
I need a dos attacks protection for a game server.
port type udp
ports 27015:27030
interface: eth0
Accept all packets from all IPs
Chek if IP sent more than 50 packets per second
Drop all packets from this IP for 5 minutes
I would be... (0 Replies)
Hi Champs
i am new in Iptables and trying to write rules for my Samba server.I took some help from internet, created one script and run from rc.local :
#Allow loopback
iptables -I INPUT -i lo -j ACCEPT
# Accept packets from Trusted network
iptables -A INPUT -s my-network/subnet -j... (0 Replies)
I want to SSH to 192.168.1.15 Server from my machine, my ip was 192.168.1.99
Source Destination was UP, with IP 192.168.1.15.
This is LAN Network there are 30 Machine's Connected to the network and working fine, I'm Playing around the local machine's because I need to apply the same rules in... (2 Replies)
Hi,
I've been struggling with this all morning and seem to have a blind spot on what the problem is. I'm trying to use iptables to block traffic on a little cluster of raspberry pi's but to allow ssh and ping traffic within it.
The cluster has a firewall server with a wifi card connecting to... (4 Replies)
Hello,
I did 2 scripts. The second one is, I hope, more secure.
What do you think?
Basic connection (no server, no router, no DHCP and the Ipv6 is disabled)
#######script one
####################
iptables -F
iptables -X -t filter
iptables -P INPUT DROP
iptables -P FORWARD... (6 Replies)
Discussion started by: Thomas342
6 Replies
LEARN ABOUT CENTOS
tcp-env
tcp-env(1) General Commands Manual tcp-env(1)NAME
tcp-env - set up TCP-related environment variables
SYNOPSIS
tcp-env [ -rR ] [ -ttimeout ] program [ arg ... ]
DESCRIPTION
The input for tcp-env must be a TCP connection. tcp-env finds out information about that connection, puts the information into several
environment variables as described in tcp-environ(5), and runs program with the given arguments.
Usually tcp-env is run from inetd. It might instead be run from another server that already sets up the right environment variables; if
PROTO is set to TCP when tcp-env is invoked, tcp-env assumes that all the other variables are set up properly, and it does not check
whether the input is a TCP connection.
OPTIONS -r (Default.) Attempt to obtain TCPREMOTEINFO from the remote host.
-R Do not attempt to obtain TCPREMOTEINFO from the remote host.
-ttimeout
Give up on the TCPREMOTEINFO connection attempt after timeout seconds. Default: 30.
SEE ALSO tcp-environ(5), inetd(8)tcp-env(1)