05-03-2013
You connect to the HMC with your laptop via a browser. The serial connection is between the HMC port and the POWER4 serial port.
I never worked with these systems, so I do not know if it is the "normal" com port, of if there is an extra one.
HMC3 is
NOTHING like
HMC7.7.7 today. Also a "waste" of your time, unless you are writing a historical review of the development of HMC code.
Hope this helps!
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi All,
I've a log file call netbackup.log in all the 5 servers in location usr/netbackup.log. I dont want to login in each server and check the log file. So i wanted to have a script written to have the log information at one place.
I want to have the last 2 lines from the file... (2 Replies)
Discussion started by: suri.tyson
2 Replies
2. AIX
Hi,
I am little confused about the virtual Ethernet configuration on VIO and Client Partitions. There is alot of info on the internet but it gets more confusing....
If I have LHEA, it is very simple. Just assign LHEA (logical host ethernet adapter) to client partition -> run smitty tcpip and... (10 Replies)
Discussion started by: filosophizer
10 Replies
3. Shell Programming and Scripting
Hello,
I have a problem with the translation of the following command. In Shell the radiance-command work like that:
gensurf seitenwand rollerblind1 '-0.95*s' '0.046' '2.85-'$1'*t' 1 1
But I don't know how to deal with this command in system().
I tried this:
... (2 Replies)
Discussion started by: ergy1983
2 Replies
4. AIX
Hi,
I ssh to HMC, then vtmenu, then start a system console from there. How do I exit the console to return to HMC prompt? I've tried the following two key combinations but none of them is working: (1) ~~ (2) Ctrl+[, Shift+(
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
5. Programming
Hi !
I have one program made of several sub programs which I am trying to compile with gfortran on Fedora 14 in my system. The program was originally written in Fortran 77 and compilation command used to be -
fort77 -O2 -f -w -o life life_com.f lifetime.f minuit.f tek_life.f utilities.f... (0 Replies)
Discussion started by: cylab123
0 Replies
6. AIX
Hi,
I'm planning to update managed system firmware to new release using HMC.
This is cite from IBM documentation describing HMC managed system updates:
What I know we install new firmware to T side and in case some problems we boot P side and reject new fw on T.
So if HMC updates both T and... (0 Replies)
Discussion started by: vilius
0 Replies
7. Red Hat
hlow all,
i want to know how we do insert big file in VFS and how we do to call that file again
can anyone explain about that
thx before (0 Replies)
Discussion started by: zvtral
0 Replies
8. Solaris
Hi friends, Please let me know if there is any way to find out Major and Minor numbers of virtual file system like below:
/devices 0K 0K 0K 0% /devices
ctfs 0K 0K 0K 0% /system/contract
proc 0K 0K ... (8 Replies)
Discussion started by: nitj
8 Replies
9. AIX
Hi there
I've bought a used System p 9115-505. When I attach the LAN cable to my router the HMC receives an IP address from my router, but the HMC is unreachable. There are no open ports.
Does anybody know that problem?
Any help greatly appreciated. Greetings from Italy! (2 Replies)
Discussion started by: mediaset23
2 Replies
LEARN ABOUT DEBIAN
nsd-xfer
nsd-xfer(8) nsd 3.2.12 nsd-xfer(8)
NAME
nsd-xfer - AXFR client to transfer zones from a name server
SYNOPSIS
nsd-xfer [-4] [-6] [-a address[@port]] [-p port] [-s serial] [-T tsiginfo] [-v] -z zone -f file servers
DESCRIPTION
Nsd-xfer is program to transfer zones from a name server using AXFR. NSD is a complete implementation of an authoritative DNS nameserver.
OPTIONS
-4 Only send to IPv4 addresses.
-6 Only send to IPv6 addresses.
-a address[@port]
Specify the source address (and port) to send from.
-f file
The file to store the zone in.
-p port
Specify the port to send to.
-s serial
Specify the serial of the current zone. The zone is only transferred if the master server has a zone with a greater serial number.
-T tsiginfo
Use TSIG to verify the zone transfer. The tsiginfo file must contain the TSIG key information. The file is removed upon successful
reading of the key. The format of the tsiginfo file is described in the doc/README file (section 3.3).
-v Be more verbose.
-z zone
Specify the zone to receive.
servers
List of nameservers to try.
EXAMPLES
To run this program the standard way type:
# nsd-xfer -z foobar.cz -f foobar.cz.zone 1.2.3.4
SEE ALSO
nsd(8), nsdc(8), nsd.conf(5), nsd-checkconf(8), nsd-notify(8), nsd-patch(8), zonec(8)
AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-xfer(8)