05-03-2013
You connect to the HMC with your laptop via a browser. The serial connection is between the HMC port and the POWER4 serial port.
I never worked with these systems, so I do not know if it is the "normal" com port, of if there is an extra one.
HMC3 is
NOTHING like
HMC7.7.7 today. Also a "waste" of your time, unless you are writing a historical review of the development of HMC code.
Hope this helps!
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi All,
I've a log file call netbackup.log in all the 5 servers in location usr/netbackup.log. I dont want to login in each server and check the log file. So i wanted to have a script written to have the log information at one place.
I want to have the last 2 lines from the file... (2 Replies)
Discussion started by: suri.tyson
2 Replies
2. AIX
Hi,
I am little confused about the virtual Ethernet configuration on VIO and Client Partitions. There is alot of info on the internet but it gets more confusing....
If I have LHEA, it is very simple. Just assign LHEA (logical host ethernet adapter) to client partition -> run smitty tcpip and... (10 Replies)
Discussion started by: filosophizer
10 Replies
3. Shell Programming and Scripting
Hello,
I have a problem with the translation of the following command. In Shell the radiance-command work like that:
gensurf seitenwand rollerblind1 '-0.95*s' '0.046' '2.85-'$1'*t' 1 1
But I don't know how to deal with this command in system().
I tried this:
... (2 Replies)
Discussion started by: ergy1983
2 Replies
4. AIX
Hi,
I ssh to HMC, then vtmenu, then start a system console from there. How do I exit the console to return to HMC prompt? I've tried the following two key combinations but none of them is working: (1) ~~ (2) Ctrl+[, Shift+(
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
5. Programming
Hi !
I have one program made of several sub programs which I am trying to compile with gfortran on Fedora 14 in my system. The program was originally written in Fortran 77 and compilation command used to be -
fort77 -O2 -f -w -o life life_com.f lifetime.f minuit.f tek_life.f utilities.f... (0 Replies)
Discussion started by: cylab123
0 Replies
6. AIX
Hi,
I'm planning to update managed system firmware to new release using HMC.
This is cite from IBM documentation describing HMC managed system updates:
What I know we install new firmware to T side and in case some problems we boot P side and reject new fw on T.
So if HMC updates both T and... (0 Replies)
Discussion started by: vilius
0 Replies
7. Red Hat
hlow all,
i want to know how we do insert big file in VFS and how we do to call that file again
can anyone explain about that
thx before (0 Replies)
Discussion started by: zvtral
0 Replies
8. Solaris
Hi friends, Please let me know if there is any way to find out Major and Minor numbers of virtual file system like below:
/devices 0K 0K 0K 0% /devices
ctfs 0K 0K 0K 0% /system/contract
proc 0K 0K ... (8 Replies)
Discussion started by: nitj
8 Replies
9. AIX
Hi there
I've bought a used System p 9115-505. When I attach the LAN cable to my router the HMC receives an IP address from my router, but the HMC is unreachable. There are no open ports.
Does anybody know that problem?
Any help greatly appreciated. Greetings from Italy! (2 Replies)
Discussion started by: mediaset23
2 Replies
dc(7) Miscellaneous Information Manual dc(7)
NAME
dc - serial line/mouse/keyboard
SYNOPSIS
controller dc0 at ibus0 slot 0 vector dcintr
DESCRIPTION
The dc serial line controller provides DECstation 2100, DECstation 3100, DECstation 5000, and DECstation 5100 computer systems with key-
board, mouse, and serial communications interfaces. The serial communications interfaces on the DECstation 2100 and DECstation 3100 provide
partial modem control. The serial communications interfaces on the DECstation 5000 provide full modem control. The device special file
/dev/tty01 on a DECstation 5100 provides full modem control, while the remaining ports provide no modem control at all. All serial commu-
nications interfaces operate at baud rates from B50 to B9600, excluding B200.
The dc ports are used as follows: Usage Graphics device keyboard at 4800 BPS Mouse or tablet at 4800 BPS Communications port 1 (w/modem
control)/local terminal Communications port 2 (w/modem control)/local terminal
On all systems except the DECstation 5100, serial port 2 is used for the system console port in server (that is, non-graphics) configura-
tions. On DECstation 5100s, the serial port labeled 3 on the back of the system is always the system console port. The serial system con-
sole port always operates at 9600 BPS, 8-bits, no parity; modem control is not supported.
RESTRICTIONS
Data communications equipment attached to the console serial port in server configurations must be set to 9600 BPS, 8-bits, no parity. The
scc driver enforces this restriction.
FILES
console terminal local terminal local terminal local terminal (DECstation 5100 only)
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
dc(7)