|
|
Sponsored Content
Operating Systems
Solaris
Reinstall old hard drives
Post 302801913 by stu1811 on Thursday 2nd of May 2013 04:45:16 PM
05-02-2013
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
Discussion started by: franruiz
3 Replies
2. Linux
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Discussion started by: tamcomng
2 Replies
3. Solaris
Version: solaris 10 x86
I just got a western digital external harddrive formated with fat 32. this drive came with some setup files which is meant for windows or mac.
I want to reformat and partition this drive into two ( for solaris and windows) such that the setup files will still be there... (2 Replies)
Discussion started by: seyiisq
2 Replies
4. Filesystems, Disks and Memory
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies
5. UNIX for Dummies Questions & Answers
Looking for some clues on how to set my internal hard drives inaccessible/busy to clonezilla. Noprobe doesn't work in startup and the drive is still found.
I know I can find all hard drives using the following:
sudo fdisk -l | grep GB | awk '{print $2}' | grep -Po "^+(?=:?)"
I tried... (9 Replies)
Discussion started by: traustic
9 Replies
6. Hardware
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
Discussion started by: Lost in Cyberia
3 Replies
7. Solaris
I have three Sun Oracle Netra T5220s. I am trying to just get the processor information psrinfo or prtdiag -v from the # prompt in single user mode.
I am needing to know the commands to get to boot the CD/DVD of the Solaris OS. I am using it via Serial Port Management.
Tinkering around I... (4 Replies)
Discussion started by: nerdboy
4 Replies
8. Linux
Hello,
I have install 2 HDD in my server and now installing the Centos6.4.
I want create the LVM of those 2 HDD's so while i'm doing this it is not allowing me to select these 2 disk's from allowable disk list.
Same problem if i tried to make Software RAID with creating LVM.
Please help. (1 Reply)
Discussion started by: purushottamaher
1 Replies
9. Solaris
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Discussion started by: ssabet
5 Replies
10. UNIX for Beginners Questions & Answers
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Discussion started by: cptkirkh
5 Replies
LEARN ABOUT CENTOS
scsi-rescan
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1) NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]] OPTIONS
-a, --alltargets scan all targets, not just currently existing [default: disabled] -d enable debug [default: 0] -l activates scanning for LUNs 0--7 [default: 0] -L NUM activates scanning for LUNs 0--NUM [default: 0] -w, --wide scan for target device IDs 0--15 [default: 0--7] -c enables scanning of channels 0 1 [default: 0 / all detected ones] -r, --remove enables removing of devices [default: disabled] -f, --flush flush failed multipath devices [default: disabled] -i, --issue-lip issue a FibreChannel LIP reset [default: disabled] -u, --update look for existing disks that have been remapped -s, --resize look for resized disks and reload associated multipath devices, if applicable --forcerescan rescan existing devices --forceremove remove and readd every device (DANGEROUS) --nooptscan don't stop looking for LUNs is 0 is not found --color use coloured prefixes OLD/NEW/DEL --hosts=LIST scan only host(s) in LIST --channels=LIST scan only channel(s) in LIST --ids=LIST scan only target ID(s) in LIST --luns=LIST scan only lun(s) in LIST --sync, --nosync issue a sync / no sync [default: sync if remove] --attachpq3 tell kernel to attach sg to LUN 0 that reports PQ=3 --reportlun2 tell kernel to try REPORT_LUN even on SCSI2 devices --largelun tell kernel to support LUNs > 7 even on SCSI2 devs --sparselun tell kernel to support sparse LUN numbering Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended). LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.) SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi sg3_utils Homepage: http://sg.danny.cz/sg rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)