Sponsored Content
Full Discussion: Sunfire X4100 server
Operating Systems Solaris Sunfire X4100 server Post 302801687 by DukeNuke2 on Thursday 2nd of May 2013 12:20:08 PM
Old 05-02-2013
The X4100 is a X86 server, so there is no ok prompt only a bios screen. connect to the serial management port and setup a IP address for the ILOM.

check the documentation for the procedures:
Sun Fire X4100 Server Product Library Documentation
This User Gave Thanks to DukeNuke2 For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

X4100 Bios RAID question

Hi there the Sunfire X4100 has a great tool that you can get to from BIOS called the configuration utility which allows you to set up Disk mirroring (RAID 1) before the OS sees it, which is great and it works a treat, however, we have a large datacentre across multiuple sites and I need to find... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

2. Solaris

check firmaware revision on X4100

Hi there I am running solaris 10 on an SunFire x4100 ...(x86 box) Could anybody tell me if there is a way I can check the firmware revision without taking the box down to do it ...eeprom doesnt give me the info I require Cheers (0 Replies)
Discussion started by: hcclnoodles
0 Replies

3. Solaris

ILOM Configuration in Galaxy x4100 server

Hai All I rquire a small help for Galaxy x4100 server, when we are trying to sepup ILOM through CLI it gives following error on commitpending=true steps. set pendingipaddress=172.21.142.158 Set 'pendingipaddress' to '172.21.142.158' -> set pendingipgateway=172.21.142.5 Set... (1 Reply)
Discussion started by: sure.solaris
1 Replies

4. Solaris

How to change boot slot X4100?

Hi everyone, I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1. When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies

5. Solaris

Does the Sun fire x4100 support HVM?

I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies

6. Solaris

Break command on rsc of sunfire v890 server

Hi Gurus I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies

7. Solaris

How to boot from Cd-rom in Server Sunfire v250?

Howto boot from Cd-rom in Server Sunfire v250? The system can't boot because the filesystem is corrupt. The system say: run manually fsck -F ufs /dev/rdsk/c0t0d0s5 But, I don't now how to make this. I tried use stop + a, but nothing hapend. Someone can I help? (13 Replies)
Discussion started by: vigux
13 Replies

8. Hardware

sun x4100 M2 processors

hi please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition. thanks (2 Replies)
Discussion started by: bahjatm
2 Replies

9. Hardware

Sun X4100 graphics

Hello all. I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots. thanks (4 Replies)
Discussion started by: petebarchetta
4 Replies

10. Hardware

Multi-bit ECC Error on X4100 M2 Server Sun Fire

I have a problem, I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited). The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable" I have... (5 Replies)
Discussion started by: hhaswan
5 Replies
Ns_Url(3aolserver)					   AOLserver Library Procedures 					Ns_Url(3aolserver)

__________________________________________________________________________________________________________________________________________________

NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines SYNOPSIS
#include "ns.h" int Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl) int Ns_ParseUrl(char *url, char **pprotocol, char **phost, char **pport, char **ppath, char **ptail) char * Ns_RelativeUrl(char *url, char *location) char * Ns_SkipUrl(Ns_Request *request, int n) _________________________________________________________________ DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl) Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR. Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail) Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref- erence in the passed-in pointers. The passed-in url will be modified. Ns_RelativeUrl(url, location) If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the relative url in the passed-in url, or NULL if error. Will set errno on error. Ns_SkipUrl(request, n) Return a pointer n elements into the request's url. SEE ALSO
nsd(1), info(n) KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)
All times are GMT -4. The time now is 10:40 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy