Sponsored Content
Full Discussion: Sunfire X4100 server
Operating Systems Solaris Sunfire X4100 server Post 302801687 by DukeNuke2 on Thursday 2nd of May 2013 12:20:08 PM
Old 05-02-2013
The X4100 is a X86 server, so there is no ok prompt only a bios screen. connect to the serial management port and setup a IP address for the ILOM.

check the documentation for the procedures:
Sun Fire X4100 Server Product Library Documentation
This User Gave Thanks to DukeNuke2 For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

X4100 Bios RAID question

Hi there the Sunfire X4100 has a great tool that you can get to from BIOS called the configuration utility which allows you to set up Disk mirroring (RAID 1) before the OS sees it, which is great and it works a treat, however, we have a large datacentre across multiuple sites and I need to find... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

2. Solaris

check firmaware revision on X4100

Hi there I am running solaris 10 on an SunFire x4100 ...(x86 box) Could anybody tell me if there is a way I can check the firmware revision without taking the box down to do it ...eeprom doesnt give me the info I require Cheers (0 Replies)
Discussion started by: hcclnoodles
0 Replies

3. Solaris

ILOM Configuration in Galaxy x4100 server

Hai All I rquire a small help for Galaxy x4100 server, when we are trying to sepup ILOM through CLI it gives following error on commitpending=true steps. set pendingipaddress=172.21.142.158 Set 'pendingipaddress' to '172.21.142.158' -> set pendingipgateway=172.21.142.5 Set... (1 Reply)
Discussion started by: sure.solaris
1 Replies

4. Solaris

How to change boot slot X4100?

Hi everyone, I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1. When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies

5. Solaris

Does the Sun fire x4100 support HVM?

I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies

6. Solaris

Break command on rsc of sunfire v890 server

Hi Gurus I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies

7. Solaris

How to boot from Cd-rom in Server Sunfire v250?

Howto boot from Cd-rom in Server Sunfire v250? The system can't boot because the filesystem is corrupt. The system say: run manually fsck -F ufs /dev/rdsk/c0t0d0s5 But, I don't now how to make this. I tried use stop + a, but nothing hapend. Someone can I help? (13 Replies)
Discussion started by: vigux
13 Replies

8. Hardware

sun x4100 M2 processors

hi please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition. thanks (2 Replies)
Discussion started by: bahjatm
2 Replies

9. Hardware

Sun X4100 graphics

Hello all. I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots. thanks (4 Replies)
Discussion started by: petebarchetta
4 Replies

10. Hardware

Multi-bit ECC Error on X4100 M2 Server Sun Fire

I have a problem, I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited). The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable" I have... (5 Replies)
Discussion started by: hhaswan
5 Replies
LAPTOP_MODE(8)						      System Manager's Manual						    LAPTOP_MODE(8)

NAME
/usr/sbin/laptop_mode - apply laptop mode settings SYNOPSIS
/usr/sbin/laptop_mode [ cmd ] [ force ] DESCRIPTION
This manual page documents briefly the /usr/sbin/laptop_mode command. laptop_mode is a program that applies the settings given in the /etc/laptop-mode/laptop-mode.conf configuration file. The primary use is to control the laptop mode feature included in Linux kernels with versions 2.6.6 and higher, and 2.4.23 and higher. This feature increases battery life by letting your hard drive spin down. This is achieved by grouping disk write activity into "chunks" that are spaced at larger intervals than they normally would be. In addition to sup- porting the Linux kernel's laptop mode feature, /usr/sbin/laptop_mode also supports various power saving modules which are configured through configuration files in the /etc/laptop-mode/conf.d directory. It is not recommended to call /usr/sbin/laptop_mode directly to start or stop laptop mode, except in hardware event handlers. To apply new configuration settings from laptop-mode.conf, call the laptop-mode service init script with the reload parameter. COMMANDS
Specify force as the second parameter to force laptop_mode to re-apply a state even if the computer is already in that state. These are the values that are allowed for cmd : auto Enable or disable laptop mode based on the current power state. Note that this will not do anything if the laptop-mode service has not been started! status Display a status report about everything that laptop_mode affects. SEE ALSO
laptop-mode.conf(8). AUTHOR
This manual page was written by Bart Samwel (bart@samwel.tk) for the Debian system (but may be used by others). Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation. On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL. LAPTOP_MODE(8)
All times are GMT -4. The time now is 06:00 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy