05-02-2013
Sunfire X4100 server
Hi,
I am currently on Sunfire X4100. This server doesn't have CDROM drive. Also I can't get to the OK prompt. From my laptop, I am connected to the management port using the Cisco Blue cable.
Please advise how can I get to the OK prompt. Also the server is so loud. Will the FAN cool down or this is how it's going to be.
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
the Sunfire X4100 has a great tool that you can get to from BIOS called the configuration utility which allows you to set up Disk mirroring (RAID 1) before the OS sees it, which is great and it works a treat, however, we have a large datacentre across multiuple sites and I need to find... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
2. Solaris
Hi there
I am running solaris 10 on an SunFire x4100 ...(x86 box) Could anybody tell me if there is a way I can check the firmware revision without taking the box down to do it ...eeprom doesnt give me the info I require
Cheers (0 Replies)
Discussion started by: hcclnoodles
0 Replies
3. Solaris
Hai All
I rquire a small help for Galaxy x4100 server, when we are trying to sepup
ILOM through CLI it gives following error on commitpending=true steps.
set pendingipaddress=172.21.142.158
Set 'pendingipaddress' to '172.21.142.158'
-> set pendingipgateway=172.21.142.5
Set... (1 Reply)
Discussion started by: sure.solaris
1 Replies
4. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
5. Solaris
I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies
6. Solaris
Hi Gurus
I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies
7. Solaris
Howto boot from Cd-rom in Server Sunfire v250?
The system can't boot because the filesystem is corrupt.
The system say:
run manually fsck -F ufs /dev/rdsk/c0t0d0s5
But, I don't now how to make this.
I tried use stop + a, but nothing hapend.
Someone can I help? (13 Replies)
Discussion started by: vigux
13 Replies
8. Hardware
hi
please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition.
thanks (2 Replies)
Discussion started by: bahjatm
2 Replies
9. Hardware
Hello all.
I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe
The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots.
thanks (4 Replies)
Discussion started by: petebarchetta
4 Replies
10. Hardware
I have a problem,
I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited).
The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable"
I have... (5 Replies)
Discussion started by: hhaswan
5 Replies
LEARN ABOUT DEBIAN
rancid
rancid(1) General Commands Manual rancid(1)
NAME
rancid - Cisco configuration filter
SYNOPSIS
rancid [-dlV] (-f filename | hostname)
DESCRIPTION
rancid is a perl(1) script which uses the login scripts (see clogin(1)) to login to a device, execute commands to display the
configuration, etc, then filters the output for formatting, security, and so on. rancid's product is a file with the name of it's last
argument plus the suffix .new. For example, hostname.new.
There are complementary scripts for other platforms and/or manufacturers that are supported by rancid(1). Briefly, these are:
agmrancid Cisco Anomaly Guard Module (AGM)
arancid Alteon WebOS switches
arrancid Arista Networks devices
brancid Bay Networks (nortel)
cat5rancid Cisco catalyst switches
cssrancid Cisco content services switches
erancid ADC-kentrox EZ-T3 mux
f10rancid Force10
f5rancid F5 BigIPs
fnrancid Fortinet Firewalls
francid Foundry and HP procurve OEMs of Foundry
hrancid HP Procurve Switches
htranicd Hitachi Routers
jerancid Juniper Networks E-series
jrancid Juniper Networks
mrancid MRTd
mrvrancid MRV optical switches
mtrancid Mikrotik routesrs
nrancid Netscreen firewalls
nsrancid Netscaler
nxrancid Cisco Nexus boxes
prancid Procket Networks
rivrancid Riverstone
rrancid Redback
srancid SMC switch (some Dell OEMs)
trancid Netopia sDSL/T1 routers
tntrancid Lucent TNT
xrancid Extreme switches
xrrancid Cisco IOS-XR boxes
zrancid Zebra routing software
The command-line options are as follows:
-V Prints package name and version strings.
-d Display debugging information.
-l Display somewhat less debugging information.
-f rancid should interpret the next argument as a filename which contains the output it would normally collect from the device (
hostname) with clogin(1).
SEE ALSO
control_rancid(1), clogin(1), rancid.conf(5)
CAVEATS
Cisco IOS offers a DHCP server that maintains a text database which can be stored remotely or on local storage. If stored locally, the
file changes constantly and causes constant diffs from rancid. If this file's name ('ip dhcp database') matches the regex
dhcp_[^[:space:].].txt, it will be filtered.
For Catalyst switches running CatOS, type cat5, the prompt must end with '>'. clogin(1) looks for '>' to determine when a login is
successful. For example:
cat5k>
cat5k> enable
Password:
cat5k> (enable)
rancid works on Cisco Catalyst 1900 series switches that are running Enterprise Edition software. This software provides a menu at
connection time that allows a command line interface to be used by entering 'K' at the prompt.
26 April 2011 rancid(1)