The instructions are in the user set up manual. Also covers things like default font and lines per inch.
You should probably also set the "CR on LF" option as well to avoid "staircased" printing (ie a subsequent line starts directly below the last character or the previous line.)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Hi,
In my application,I need to monitor the devices connected through serial port in solaris sparc 9 OS.I used c and java code for it and I am able to do the same but the problem comes when I restart the system and the open my application and try to monitor it.but I m unable to monitor the... (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi
Had an old ML590 with RS232 serial card that stopped working (spindle that advance ribbon broke) so I purchased a working used on ebay.
Printer powers up and seems fine. Put serial board from old printer in working ebay unit but no printing happens.
Does anyone know if there are any... (0 Replies)
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Hi Folks,
Here is one for the real Solaris aficionados on the site;
I have a T5240 and have to create an I/O domain with access to the serial port, in this case /dev/term/a and although I have been through the documentation I'm having some issues in identifying the device to assign.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT NETBSD
spif
SPIF(4) BSD Kernel Interfaces Manual SPIF(4)NAME
spif -- SBus (spiffy) Serial/Parallel Interface
SYNOPSIS
spif* at sbus? slot ? offset ? (sun4c/sun4m/sun4u)
stty* at spif? (sun4c/sun4m/sun4u)
sbpp* at spif? (sun4c/sun4m/sun4u)
DESCRIPTION
The spif driver provides support for the Sun Serial/Parallel Interface card (Sun part number 501-1931), which is based on the Cirrus Logic
CD180 octal serial controller and the Cirrus Logic PPC2 parallel port controller.
The device minor numbers for this driver are encoded as follows:
+---+---+---+---+---+---+---+---+
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+---+---+---+---+---+---+---+---+
| | | | | | | |
| | | | | +---+---+---> port number
| | | | |
| | | | +---------------> unused
| | | |
| | | +-------------------> dial-out (on tty ports)
| | |
| | +-----------------------> unused
| |
+---+---------------------------> card number
Up to four cards are supported in the system.
Each of the serial ports has an 8 byte FIFO for receive and transmit as well as automatic hardware (RTS/CTS) flow control.
FILES
/dev/ttyS[0123][0-7] Serial ports
/dev/bppS[0-3] Parallel ports
DIAGNOSTICS
spif%d: ccr timeout A timeout occurred while writing to one of the CD180 registers.
stty%d-%d: ring overflow Incoming characters were discarded because the application in control of the device did not read the input fast
enough.
SEE ALSO intro(4), sbus(4), tty(4)HISTORY
The spif adapter was first supported in OpenBSD 2.5. The driver was ported to NetBSD 3.0.
AUTHORS
The driver was written by Jason Wright <jason@thought.net>, and is heavily based on the magma(4) driver written by Iain Hibbert.
TODO
The parallel port is not supported yet.
Dial-out (cua) devices are not yet supported.
BSD February 4, 1999 BSD