05-01-2013
Quote:
Did you set the baud rate the same as the old printer? You have to do it through the printer front panel set up menu.
You also have to set the serial board as the active interface.
Thanks for the reply, that makes sense. Looking for the old manual to that printer.
Are those changes more than the basic user manual would cover?
---------- Post updated 05-01-13 at 09:26 AM ---------- Previous update was 04-30-13 at 07:52 PM ----------
Got it working. Had to fig out how to print settings menu
X-on/X-off
Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I have a problem on this printer. The first page is always blank, like a page drop. If you have a solution or a idea, please ?
Thanks (1 Reply)
Discussion started by: Lo38lo
1 Replies
2. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
3. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
4. Solaris
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies
5. Programming
Hi,
In my application,I need to monitor the devices connected through serial port in solaris sparc 9 OS.I used c and java code for it and I am able to do the same but the problem comes when I restart the system and the open my application and try to monitor it.but I m unable to monitor the... (2 Replies)
Discussion started by: smartgupta
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. Hardware
Hi
Had an old ML590 with RS232 serial card that stopped working (spindle that advance ribbon broke) so I purchased a working used on ebay.
Printer powers up and seems fine. Put serial board from old printer in working ebay unit but no printing happens.
Does anyone know if there are any... (0 Replies)
Discussion started by: magnetman
0 Replies
8. Linux
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
Discussion started by: cerco
25 Replies
9. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
10. Solaris
Hi Folks,
Here is one for the real Solaris aficionados on the site;
I have a T5240 and have to create an I/O domain with access to the serial port, in this case /dev/term/a and although I have been through the documentation I'm having some issues in identifying the device to assign.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT CENTOS
system-config-printer-applet
SYSTEM-CONFIG-PRIN(1) Man pages SYSTEM-CONFIG-PRIN(1)
NAME
system-config-printer-applet - print job manager
SYNOPSIS
system-config-printer-applet [--help] [--version] [--debug]
DESCRIPTION
system-config-printer-applet is a print job manager for CUPS. Normally it will display a printer icon in the notification area, greyed out
when there are no print jobs for the current user. Clicking on the icon displays a simple print job manager for cancelling or reprinting
jobs.
To save memory, the applet waits first of all until the user has printed a job before putting the icon in the notification area. To invoke
the print job manager before a job has been printed, run the applet with the --no-tray-icon option: a desktop file is provided for this, so
that it should appear in the system menu.
As well as displaying a printer icon in the notification area, the applet also provides a D-BUS server for the
com.redhat.PrintDriverSelection interface, to help configure a new printer when it is plugged in.
OPTIONS
--help
Display a short usage message.
--version
Display the version of the applet.
--debug
Show debugging information.
AUTHOR
Tim Waugh <twaugh@redhat.com>
Author.
system-config-printer 24 Nov 2010 SYSTEM-CONFIG-PRIN(1)