04-30-2013
Did you set the baud rate the same as the old printer? You have to do it through the printer front panel set up menu.
You also have to set the serial board as the active interface.
Last edited by jgt; 04-30-2013 at 03:19 PM..
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I have a problem on this printer. The first page is always blank, like a page drop. If you have a solution or a idea, please ?
Thanks (1 Reply)
Discussion started by: Lo38lo
1 Replies
2. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
3. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
4. Solaris
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies
5. Programming
Hi,
In my application,I need to monitor the devices connected through serial port in solaris sparc 9 OS.I used c and java code for it and I am able to do the same but the problem comes when I restart the system and the open my application and try to monitor it.but I m unable to monitor the... (2 Replies)
Discussion started by: smartgupta
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. Hardware
Hi
Had an old ML590 with RS232 serial card that stopped working (spindle that advance ribbon broke) so I purchased a working used on ebay.
Printer powers up and seems fine. Put serial board from old printer in working ebay unit but no printing happens.
Does anyone know if there are any... (0 Replies)
Discussion started by: magnetman
0 Replies
8. Linux
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
Discussion started by: cerco
25 Replies
9. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
10. Solaris
Hi Folks,
Here is one for the real Solaris aficionados on the site;
I have a T5240 and have to create an I/O domain with access to the serial port, in this case /dev/term/a and although I have been through the documentation I'm having some issues in identifying the device to assign.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
iscc(7) Miscellaneous Information Manual iscc(7)
NAME
iscc - serial communications interface
SYNOPSIS
controller iscc0 at isa0
DESCRIPTION
An onboard Zilog 8530 DUART provides AXPvme-based Single Board Computers with console (CON) and auxiliary (AUX) serial communications
ports. Both serial communications ports can operate at baud rates from B50 to B38400, excluding B134 (see tty(7)).
On AXPvme Single Board Computers configured with a graphics head as the system console, the CON serial communications port (/dev/tty01) is
available for use by application programs as an additional communications port.
In the absence of a graphics head, the CON serial communications port (/dev/console) becomes the system console. When used as the serial
system console, the CON serial communications port always operates at 9600 BPS, 8-bits, and no parity.
Regardless of system console, the AUX serial communications port (/dev/tty00) is always available for use by application programs.
RESTRICTIONS
Data communications equipment attached to the CON serial communications port must be set to 9600 BPS, 8-bits, no parity when configured as
the serial system console. The iscc terminal driver enforces this restriction.
No modem control is supported for either the CON or AUX serial communications ports.
FILES
console terminal local terminal local terminal
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
iscc(7)