I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
Code:
# raidctl
Controller: 2
#
#
# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <Sun-STK RAID INT-V1.0-68.25GB>
/pci@400/pci@0/pci@c/scsi@0/disk@0,0
1. c1t1d0 <Sun-STK RAID INT-V1.0-68.25GB>
/pci@400/pci@0/pci@c/scsi@0/disk@1,0
2. c1t2d0 <Sun-STK RAID INT-V1.0-68.25GB>
/pci@400/pci@0/pci@c/scsi@0/disk@2,0
3. c1t3d0 <Sun-STK RAID INT-V1.0-68.25GB>
/pci@400/pci@0/pci@c/scsi@0/disk@3,0
Specify disk (enter its number): ^C
# cfgadm -avl
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c1 connected configured unknown
unavailable scsi-bus n /devices/pci@400/pci@0/pci@c/scsi@0:scsi
c1::dsk/c1t0d0 connected configured unknown Sun STK RAID INT
unavailable disk n /devices/pci@400/pci@0/pci@c/scsi@0:scsi::dsk/c1t0d0
c1::dsk/c1t1d0 connected configured unknown Sun STK RAID INT
unavailable disk n /devices/pci@400/pci@0/pci@c/scsi@0:scsi::dsk/c1t1d0
c1::dsk/c1t2d0 connected configured unknown Sun STK RAID INT
unavailable disk n /devices/pci@400/pci@0/pci@c/scsi@0:scsi::dsk/c1t2d0
c1::dsk/c1t3d0 connected configured unknown Sun STK RAID INT
unavailable disk n /devices/pci@400/pci@0/pci@c/scsi@0:scsi::dsk/c1t3d0
c2 connected unconfigured unknown
unavailable scsi-sata n /devices/pci@400/pci@0/pci@8/scsi@0:scsi
c3 connected unconfigured unknown
unavailable fc n /devices/pci@400/pci@0/pci@9/SUNW,qlc@0/fp@0,0:fc
c4 connected unconfigured unknown
unavailable fc n /devices/pci@400/pci@0/pci@9/SUNW,qlc@0,1/fp@0,0:fc
c5 connected unconfigured unknown
unavailable fc n /devices/pci@400/pci@0/pci@d/SUNW,qlc@0/fp@0,0:fc
c6 connected unconfigured unknown
unavailable fc n /devices/pci@400/pci@0/pci@d/SUNW,qlc@0,1/fp@0,0:fc
usb0/1 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0:2
usb0/3 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0:3
usb1/1 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,1:1
usb1/2 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,1:2
usb2/1 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2:1
usb2/2 connected configured ok Mfg: Texas Instruments Incorporated Product: 6250 FW: 03.05.02.22.562AD423 NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-storage n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2:2
usb2/3 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2:3
usb2/4 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-hub n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2:4
usb2/4.1 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2/hub@4:4.1
usb2/4.2 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2/hub@4:4.2
usb2/4.3 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2/hub@4:4.3
usb2/4.4 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2/hub@4:4.4
usb2/5 empty unconfigured ok
unavailable unknown n /devices/pci@400/pci@0/pci@1/pci@0/usb@0,2:5
#
On the OBP :
Code:
{0} ok probe-scsi-all
/pci@400/pci@0/pci@d/SUNW,qlc@0,1
QLogic QLE2462 Host Adapter Driver(SPARC): 1.24 11/15/06
Firmware version 4.00.26
Fibre Channel Link down
Possible causes: No cable, incorrect connection mode or data rate
/pci@400/pci@0/pci@d/SUNW,qlc@0
QLogic QLE2462 Host Adapter Driver(SPARC): 1.24 11/15/06
Firmware version 4.00.26
Fibre Channel Link down
Possible causes: No cable, incorrect connection mode or data rate
/pci@400/pci@0/pci@c/scsi@0
Waiting for AAC Controller to start: . . Started
AAC Kernel Version: 15825
Target 0 Volume 0
Unit 0 Disk Adaptec RAID ASR5805 V1.0 143134721 Blocks, 73 GB
Target 1 Volume 1
Unit 0 Disk Adaptec RAID ASR5805 V1.0 143132673 Blocks, 73 GB
Target 2 Volume 2
Unit 0 Disk Adaptec RAID ASR5805 V1.0 143134721 Blocks, 73 GB
Target 3 Volume 3
Unit 0 Disk Adaptec RAID ASR5805 V1.0 143134721 Blocks, 73 GB
/pci@400/pci@0/pci@9/SUNW,qlc@0,1
QLogic QLE2462 Host Adapter Driver(SPARC): 1.24 11/15/06
Firmware version 4.00.26
Fibre Channel Link down
Possible causes: No cable, incorrect connection mode or data rate
/pci@400/pci@0/pci@9/SUNW,qlc@0
QLogic QLE2462 Host Adapter Driver(SPARC): 1.24 11/15/06
Firmware version 4.00.26
Fibre Channel Link down
Possible causes: No cable, incorrect connection mode or data rate
/pci@400/pci@0/pci@8/scsi@0
MPT Version 1.05, Firmware Version 1.27.00.00
ERROR: /pci@400: Last Trap: Fast Data Access MMU Miss
{0} ok
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
04-26-2013
