04-20-2013
There is no way I'm aware of to tune a ZFS pool for such a mirror.
The usual way to take advantage of SSD based storage with ZFS is to set up a L2ARC to improve read performance and a ZIL device for write one.
https://blogs.oracle.com/brendan/entry/test
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
When I was using windowsXP I encountered a file manager called UltraExplorer http://www.mustangpeak.net/ultraexplorer.html that appeared really impressive.
Now in the Linux/UNIX world I was pointed towards a similar idea called 4Pane
http://www.4pane.co.uk/
I'm surprised to do a search on... (3 Replies)
Discussion started by: catch22
3 Replies
2. Solaris
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
Discussion started by: Lespaul20
3 Replies
3. Solaris
Hello All,
In the output of the command "mpdcontrol -no xlist", I found that, some of the preferred paths are marked as "err". You can see the output below:
# mpdcontrol -noxlist
Unit Dev# MPD_ID/Policy DeviceName FC_AL DevMajMin IOcnt State... (0 Replies)
Discussion started by: sundar3350
0 Replies
4. Solaris
Hi ,
I am new to SVM .when i try to learn RAID 1 , first they are creating two RAID 0 strips through
metainit d51 1 1 c0t0d0s2
metainit d52 1 1 c1t0d0s2
In the next step
metainit d50 -m d51
d50: Mirror is setup
next step is
metaattach d50 d52
d50 : submirror d52 is... (7 Replies)
Discussion started by: vr_mari
7 Replies
5. AIX
Hi,
lets say we have two boot interfaces en0 en1
and two resource groups, with two service ips, sip1 and sip2, one persistent ip pers1
both persistend and service ips are applied as ip-alias
when I start the cluster, and bring the resource groups up, it looks like
en0: sip1 and sip2
... (4 Replies)
Discussion started by: funksen
4 Replies
6. IP Networking
I rotate between a static lan, dhcp lan, and various wireless networks daily. Is there a way to set preferred network connections? I use some static ip's daily, some static ip's like once a month, and almost never use the dhcp lan. The same I do with my various wireless networks. Some I use daily... (0 Replies)
Discussion started by: cokedude
0 Replies
7. Solaris
Hi all,
After being dumped in a Solaris sysadmin role, i have been trying to tidy the unpatched mess I have inherited. Part of this task is to update the current AMP stack.
The current stack is Webstack 1.5, which was current in 2009, and as far as I can see, no longer supported. Post the... (2 Replies)
Discussion started by: Sol-nova
2 Replies
8. HP-UX
what is the difference between DRD and Root Mirror Disk using LVM mirror ? (3 Replies)
Discussion started by: maxim42
3 Replies
9. Solaris
Hello,
I am upgrading Veritas from 5.1 to 6.0.1/6.0.5 in a Solaris 10 u8 server with OS mirrored (rpool) in zfs/zpool configuration.
I need to split it to have a quick way to backout in case of failure (make splitted mirror side bootable for a quick revert, like booting from it). I remember... (3 Replies)
Discussion started by: feroccimx
3 Replies
LEARN ABOUT FREEBSD
zfsboot
ZFSBOOT(8) BSD System Manager's Manual ZFSBOOT(8)
NAME
zfsboot -- bootcode for ZFS on BIOS-based computers
DESCRIPTION
zfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool. zfsboot is installed in two parts on a disk or a partition
used by a ZFS pool. The first part, a single-sector starter boot block, is installed at the beginning of the disk or partition. The second
part, a main boot block, is installed at a special offset within the disk or partition. Both areas are reserved by the ZFS on-disk specifi-
cation for boot use. If zfsboot is installed in a partition, then that partition should be made bootable using appropriate configuration and
boot blocks described in boot(8).
BOOTING
The zfsboot boot process is very similar to that of gptzfsboot(8). One significant difference is that zfsboot does not currently support the
GPT partitioning scheme. Thus only whole disks and MBR partitions, traditionally referred to as slices, are probed for ZFS disk labels. See
the BUGS section in gptzfsboot(8) for some limitations of the MBR scheme support.
USAGE
zfsboot supports all the same prompt and configuration file arguments as gptzfsboot(8).
FILES
/boot/zfsboot boot code binary
/boot.config parameters for the boot block (optional)
/boot/config alternative parameters for the boot block (optional)
EXAMPLES
zfsboot is typically installed using dd(1). To install zfsboot on the ada0 drive:
dd if=/boot/zfsboot of=/dev/ada0 count=1
dd if=/boot/zfsboot of=/dev/ada0 iseek=1 oseek=1024
If the drive is currently in use, the GEOM safety will prevent writes and must be disabled before running the above commands:
sysctl kern.geom.debugflags=0x10
zfsboot can also be installed in an MBR slice:
gpart create -s mbr ada0
gpart add -t freebsd ada0
gpart create -s BSD ada0s1
gpart bootcode -b /boot/boot0 ada0
gpart set -a active -i 1 ada0
dd if=/boot/zfsboot of=/dev/ada0s1 count=1
dd if=/boot/zfsboot of=/dev/ada0s1 iseek=1 oseek=1024
Note that commands to create and populate a pool are not shown in the example above.
SEE ALSO
dd(1), boot.config(5), boot(8), gptzfsboot(8), loader(8), zfsloader(8), zpool(8)
HISTORY
zfsboot appeared in FreeBSD 7.3.
AUTHORS
This manual page was written by Andriy Gapon <avg@FreeBSD.org>.
BUGS
Installing zfsboot with dd(1) is a hack. ZFS needs a command to properly install zfsboot onto a ZFS-controlled disk or partition.
BSD
September 15, 2014 BSD