04-13-2013
I have been at customer locations where they only used AIX MPIO, and nothing propioratory. Main issue is how to get/maintain multi-path load-balancing.
Again,what I often see is that the disks are configured as no_reserve and round_robin.
Test, Test, Test!
Hope this helps. (In short, I do not know of a reason why it should not work).
10 More Discussions You Might Find Interesting
1. HP-UX
Hi all,
I am trying to configure my HPUX host 11.31 IA64 to boot from a LUN for EMC clariion CX3-80 (Flaire PNR 26).
I am following the below mentioned steps..
vi /tmp/idf
3
EFI 500MB
HPUX 100%
HPSP 400MB
idisk -f /tmp/idf -w /dev/rdisk/diskxxx
insf -e
pvcreate -B... (0 Replies)
Discussion started by: barun agarwal
0 Replies
2. Red Hat
hi all,
i have qle 2460 hba card in my server. and i have a lun from promise array from raid 0. I want to boot my OS (rhel5.2-64 bit) lun on a dell t300 server. can some one help me on this please asap.. (0 Replies)
Discussion started by: navadeep
0 Replies
3. Solaris
My current situation is like this, I have a v440 connected to a netapp central storage 3140 via fiber channel, my OS and oracle is installed in the internal drive of the v440.
What I would like to do is to advertise another LUN in netapp to the v440 and let my v440 boot from it so I can start... (3 Replies)
Discussion started by: q8devilish
3 Replies
4. UNIX for Advanced & Expert Users
Hi There,
Has anyone had any luck with or know how to get AIX 5+ to boot from a HP EVA 6000 SAN?
The servers used here will be P Class Blades
My initial searches on this so far did not bring results so I am guessing this may not be possible on HP SAN's but please let me know if I am... (0 Replies)
Discussion started by: fazzasx
0 Replies
5. AIX
Hello, we have a wierd and urgent problem, with a few of our p595 LPARs running AIX 5.3. The LPARs ran AIX 5.3 TL 7 and booted off EMC SAN disks, using EMC Powerpath. Every boot we run "pprootdev on" and "pprootdev fix". We can issue "bosboot -a" and we can reboot the machines.
Now, on two... (2 Replies)
Discussion started by: rwesterik
2 Replies
6. Solaris
I have a solaris 10 box which does not have internal disks it has just a single dual port HBA card. Storage team has assigned 2 LUNs to the system and i can see it from the probe-scsi-all
/pci@3,700000/SUNW,emlxs@0,1
Device PortID 10100 WWPN 5006016941e0a08d
LUN 0 Disk DGC ... (0 Replies)
Discussion started by: fugitive
0 Replies
7. AIX
Hi All..
On to a new implementation with AIX 7.1 san boot from EMC disks (Using NPIV). Anyone played with this recently?
Wondering if we need PowerPath on the AIX clients or has native MPIO matured to replace it. Thoughts?
Thanks
Mr B (6 Replies)
Discussion started by: balaji_prk
6 Replies
8. Solaris
How to identify the server is BOOT FROM SAN.
Also how one can find from which device it is booted?
Thanks
Rahul
Double post, continued here (0 Replies)
Discussion started by: rahul.kurumkar
0 Replies
9. Red Hat
Hi, I have many servers all of these are boot from SAN. Can anybody let me know that how to identify the server is Boot fron SAN and from which device?
Thanks
Rahul (1 Reply)
Discussion started by: rahul.kurumkar
1 Replies
10. Red Hat
I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Discussion started by: rbatte1
4 Replies
LEARN ABOUT MOJAVE
test::use::ok
Test::use::ok(3) User Contributed Perl Documentation Test::use::ok(3)
NAME
Test::use::ok - Alternative to Test::More::use_ok
SYNOPSIS
use ok 'Some::Module';
DESCRIPTION
According to the Test::More documentation, it is recommended to run "use_ok()" inside a "BEGIN" block, so functions are exported at
compile-time and prototypes are properly honored.
That is, instead of writing this:
use_ok( 'Some::Module' );
use_ok( 'Other::Module' );
One should write this:
BEGIN { use_ok( 'Some::Module' ); }
BEGIN { use_ok( 'Other::Module' ); }
However, people often either forget to add "BEGIN", or mistakenly group "use_ok" with other tests in a single "BEGIN" block, which can
create subtle differences in execution order.
With this module, simply change all "use_ok" in test scripts to "use ok", and they will be executed at "BEGIN" time. The explicit space
after "use" makes it clear that this is a single compile-time action.
SEE ALSO
Test::More
CC0 1.0 Universal
To the extent possible under law, XX has waived all copyright and related or neighboring rights to Test-use-ok.
This work is published from Taiwan.
<http://creativecommons.org/publicdomain/zero/1.0>
POD ERRORS
Hey! The above document had some coding errors, which are explained below:
Around line 45:
Non-ASCII character seen before =encoding in 'XX'. Assuming UTF-8
perl v5.18.2 2012-09-11 Test::use::ok(3)