04-10-2013
Quote:
Originally Posted by
rupeshkp728
I am using just n and not "n N" and still its showing me further lines though not executing them.
This is what I want to convey. Simply using 'n' and it behaves like 'n 1' as default. In your case it's 'n 7' as default. So just try explicitly as 'n 1' and see what happens. You may also try 'n -6' , 'n -2', 'n -1' to observe what happens.
My suggestion:
Just look at the release note of the GDB version your using or the latest manual for 'stepping' and/or 'next' behavior of the latest release.
This User Gave Thanks to Praveen_218 For This Post:
10 More Discussions You Might Find Interesting
1. Programming
Which is better??
I have always been a gdb fan.. But ppl say dbx is beter better for debugging the core.. Do all GDB lovers agree to it???
:cool: (1 Reply)
Discussion started by: jyotipg
1 Replies
2. Programming
Can anyone give me the link to a website having gdb tutorials
(for advanaced debugging & shortcuts)
http://www.burneddowndays.com/talk/YaBBImages/rolleyes.gif (1 Reply)
Discussion started by: wojtyla
1 Replies
3. Solaris
I want to install gdb on SunOS 5.6 machine. Where can i download from ? (1 Reply)
Discussion started by: shafi2all
1 Replies
4. UNIX for Advanced & Expert Users
Hi,
This is a simple question on GDB. Given a core file, how can you check which process has dumped the core?
Regards
- Krishna (1 Reply)
Discussion started by: krishnamurthig
1 Replies
5. UNIX for Advanced & Expert Users
Hi All,
I wanted to know if there is a core file generated and I am not sure for which Binary it is generated .
Can I use gdb to debug the core file ?
Thanks. (1 Reply)
Discussion started by: shubhranshu
1 Replies
6. UNIX for Advanced & Expert Users
Hi All,
I am trying to execute a binary and it is giving Segmentation Fault.
Can I use gdb to debug this error?
Secondly there is no core file generated , so when I an trying to run gdb with the binary only I am not able to set any breakpoints.
When I am running the gdb and the I am... (1 Reply)
Discussion started by: shubhranshu
1 Replies
7. Programming
Hello,
I am having problem with debugging my code. I am writing a C code and then I compile it with the Makefile. I make a target file and then copy it in my Robot(Khepera III) and then run the program over there.
I compile it ofcorse on my machine and then copy the compiled file in the... (10 Replies)
Discussion started by: mind@work
10 Replies
8. Programming
i have created some break points in gdb.
let's say....
b sqlcxt
how can i know the breakpoint name of sqlcxt ??? (1 Reply)
Discussion started by: lipun4u
1 Replies
9. Programming
Hi, I got:
host machine: RedHat (RHEL6)
virtual machine: RedHat (RHEL6)
I run (on host machine):
qemu-system-x86_64 ...... -S -s
after that i run (on host machine):
gdb
target remote localhost:1234
set architecture i386:x86-64
and then i can use (on host machine) 'ctrl + c' to... (2 Replies)
Discussion started by: Chrisdot
2 Replies
10. Programming
Hi, all
I try to understand the output from gdb
Program received signal SIGABRT, Aborted.
*** glibc detected *** /home/sys_cbo/dev/zif/bin/Debug/zifd: free(): invalid pointer: 0x00007fffac04d3d0 ***
how should i read this?
(gdb) backtrace
#0 0x0000003015e32925 in raise () from... (1 Reply)
Discussion started by: huvcbo
1 Replies
LEARN ABOUT FREEBSD
dcons
DCONS(4) BSD Kernel Interfaces Manual DCONS(4)
NAME
dcons -- dumb console device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
options GDB
device firewire
device dcons
Alternatively, to load the driver as a module at boot time, place the following line in your kernel configuration file:
options GDB
and in loader.conf(5):
dcons_load="YES"
DESCRIPTION
The dcons device is a simple console device which just reads from and writes to an allocated buffer for input and output respectively. It is
of no use by itself and it is supposed that the buffer is accessed via a bus like firewire(4) or kvm(3) for interaction.
The buffer consists of 4 channels. There are 2 ports, one for the console TTY and another is GDB port, then each port has an input channel
and an output channel.
FILES
/dev/dcons
/etc/ttys
EXAMPLES
If you want to run getty(8) on dcons, insert the following line into ttys(5) and send a HUP signal to init(8) using kill(1).
dcons "/usr/libexec/getty std.9600" vt100 on secure
Once the fwohci(4) device is initialized to allow physical access, the buffer can be accessed from another host via a firewire(4) bus using
the dconschat(8) application. See dconschat(8) for more details.
If you want to use dcons(4) as a gdb(1) port, add the following line into loader.conf(5):
dcons_gdb="1"
SEE ALSO
dcons_crom(4), ddb(4), firewire(4), fwohci(4), gdb(4), ttys(5), conscontrol(8), dconschat(8), fwcontrol(8)
AUTHORS
Hidetoshi Shimokawa <simokawa@FreeBSD.org>
BUGS
This driver is currently under development.
BSD
January 26, 2008 BSD