04-04-2013
before to try the varyonvg, could you check if lspv shows the same content in both nodes
I not have experience in XIV, but in another Storage Copies (EMC, HDS), probably you need clean the reservations that the original system put in the physical devices.
I think tyhat you need heck that the attributes on same nodes are the same, use lsattr -El hdiskX to review these, in special the reservation policy values.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello all,
Strange problem on p5 520 server. I've created two volume groups, filesystems, etc.. Everything working fine, without any problem. After some tests with a DS4300 unit I wanted to remove the volume groups, change the DS4300 configuration, and re-create a new volumegroup. However, I'm... (0 Replies)
Discussion started by: EricBE
0 Replies
2. UNIX for Dummies Questions & Answers
I am trying to move a file that is in the root directory. I suspect it is an old file created by someone when the system was installed. I am testing accessing the file by doing a copy but the command does not find the file.
I am operating as root. We are HP-UX B.11.23
I do long listing and... (3 Replies)
Discussion started by: phcorn
3 Replies
3. AIX
Good evening,
Thanks a lot for your help, we appreciate it a bunch. Heres basically a summary of what we have (sorry Im adding some extra history as well):
We have 2 Ibm Servers (Hag and Aki) that are running AIX Version 5. Each connect to a SAN device via 2 separate fiber paths. Hag seems to... (9 Replies)
Discussion started by: aix-olympics
9 Replies
4. AIX
Hi all.
I'm new to AIX, so... We are running a BCV process between two AIX 5 machines attached to EMC Clariion SAN. During the varyonvg portion of the BCV process, we experienced a failure due to the physical volume is marked missing (PVMISSING). What diagnostics can I run to see the missing... (2 Replies)
Discussion started by: KSFlyer
2 Replies
5. AIX
Hello,
On Aix 5.3, during importvg, the varyonvg fails:
importvg -y vgtest hdisk20
0516-013 varyonvg: The volume group cannot be varied on because
there are no good copies of the descriptor area.
When i use manually the command varyonvg -u -b -t vgtest to force, the vg can... (3 Replies)
Discussion started by: dantares
3 Replies
6. Solaris
Hi,
I'm learning for my Solaris 10 sys-admin part 2. I'm now trying to get nis working because for the exercise. I run in to a problem.
Setup:
Three Systems
solaris101 (client)
Nothing wrong here havent made any config changes yet.
solaris102 (master server)
Interfaces
... (1 Reply)
Discussion started by: jld
1 Replies
7. Solaris
Hi guys,
I had a solaris box, with veritas controled disk.
1 disc is showing soft errors, how can I repair the soft errors?
Please help.
Cheers; (4 Replies)
Discussion started by: Mujakol
4 Replies
8. Shell Programming and Scripting
I am trying to move content of a folder usingls /backup/db_backups/INCREMENTAL/|while read file ; do
mv $file /backup_LOCAL/db_backups/INCREMENTAL/
done...but when I run this command using a bash script I'm getting this error ./test.sh
mv: cannot stat... (6 Replies)
Discussion started by: rocking77
6 Replies
9. AIX
Iam new to AIX
I am unable varyonvg on the vios,some of the disk are reported as harware failure.
I am going to replace the disk,Please tell me how to remove the disk without any corruption in the VG
lspv -l hdiskx also didn't work (0 Replies)
Discussion started by: roayaix
0 Replies
10. AIX
Hi there,
I am trying to determine if a specific XIV LUN on AIX is in OPEN or CLOSED state. I would like tthe same info as I can get from pcmpath command on v7000 LUN-s. I would need this info to find out if I can safely delete a LUN or not.
I tried fuser command, but no luck. It did not... (6 Replies)
Discussion started by: trifo75
6 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)