04-02-2013
Actually this command is better: mount
10 More Discussions You Might Find Interesting
1. Solaris
Hi everyone,
I wonder if I can canvas any opinions or thoughts (good or bad) on SAN attaching a SUN V880/490 to an EMC Clarion SAN?
At the moment the 880 is using 12 internal FC-AL disks as a db server and seems to be doing a pretty good job. It is not I/O, CPU or Memory constrained and the... (2 Replies)
Discussion started by: si_linux
2 Replies
2. Filesystems, Disks and Memory
I'm setting up a CentOS 5 server that will be connected to an HP EVA4000. My previous experience is with an HP VA7400 and HP-UX. In HP-UX I can add "alternate paths" to a volume group in order to have redundant paths to the SAN via dual fiber channel HBAs just by either adding them with... (3 Replies)
Discussion started by: deckard
3 Replies
3. Linux
Hello everyone.
I was wondering if there is a way to increase the size on the LUN on a SAN and make the Linux kernel understand the changes without restarting?
In the past it has always been rebooted to see the new values but im sure that there is a way now for the lvm to see the Free PE in... (8 Replies)
Discussion started by: d_ark
8 Replies
4. Filesystems, Disks and Memory
Am trying to differentiate between the local disks and LUN's presented from SAN onto the server. Have Tried fdisk -l, however I quite cudn't differentiate the local disks from SAN presented LUN's.
Can you pls. let me know the procedure and commands to find this.
OS - RHEL 4
SAN - EMC... (3 Replies)
Discussion started by: Crazy_murli
3 Replies
5. Filesystems, Disks and Memory
Hi All,
Storage team assigned same SAN disk on two servers
how to create same paritations from same SAN disk on two linux servers
may i know options & procedure. But here one server writing on SAN disk and another server reading other files from SAN disks
Thanks in advance (1 Reply)
Discussion started by: kurva
1 Replies
6. AIX
Hi,everyone
the situation is: at the very beginning ,through cfgmgr i find all LTO3 drives and 9840D drives. Then, some guy changed the device id(loop id) of all the stk drives on the tape lib panel. This time, i ran the cfgmgr but got nothing.
so i asked that guy to change the loop id... (2 Replies)
Discussion started by: zzisking
2 Replies
7. AIX
How to find the status of SAN Disc through command prompt (1 Reply)
Discussion started by: AIXlearner
1 Replies
8. AIX
Can someone point me in the right direction as to where I can find information on how to cleanly disconnect my AIX 5.3 host from our DS/4200 SAN. I have to do a firmware upgrade on the SAN.
-Thanks (2 Replies)
Discussion started by: tfort73
2 Replies
9. Solaris
We have a Sun M5000 connecting to a Brocade SAN switch. I don't know the IP of the Brocade switch and don't want to use its serial port to get the info. How can I find the IP of the Brocade switch under Solaris 10? Snoop is not supported by Solaris multipathing. What other tools can I use to find... (6 Replies)
Discussion started by: aixlover
6 Replies
10. Red Hat
Hi folks,
How to identify the SAN is running in Single path or dual source path for linux servers. (2 Replies)
Discussion started by: gsiva
2 Replies
LEARN ABOUT SUSE
extlinux
extlinux(1) General Commands Manual extlinux(1)
NAME
extlinux - install the SYSLINUX bootloader on a ext2/ext3 filesystem
SYNOPSIS
extlinux [options] directory
DESCRIPTION
EXTLINUX is a new syslinux derivative, which boots from a Linux ext2/ext3 filesystem. It works the same way as SYSLINUX, with a few slight
modifications. It is intended to simplify first-time installation of Linux, and for creation of rescue and other special-purpose boot
disks.
The installer is designed to be run on a mounted directory. For example, if you have an ext2 or ext3 usb key mounted on /mnt, you can run
the following command:
extlinux --install /mnt
OPTIONS
-H, --heads=#
Force the number of heads.
-i, --install
Install over the current bootsector.
-O, --clear-once
Clear the boot-once command.
-o, --once=command
Execute a command once upon boot.
-r, --raid
Fall back to the next device on boot failure.
--reset-adv
Reset auxiliary data.
-S, --sectors=#
Force the number of sectors per track.
-U, --update
Updates a previous EXTLINUX installation.
-z, --zip
Force zipdrive geometry (-H 64 -S 32).
BUGS
I would appreciate hearing of any problems you have with SYSLINUX. I would also like to hear from you if you have successfully used SYS-
LINUX, especially if you are using it for a distribution.
If you are reporting problems, please include all possible information about your system and your BIOS; the vast majority of all problems
reported turn out to be BIOS or hardware bugs, and I need as much information as possible in order to diagnose the problems.
There is a mailing list for discussion among SYSLINUX users and for announcements of new and test versions. To join, send a message to
majordomo@linux.kernel.org with the line:
SEE ALSO
syslinux(1)
SYSLINUX for ext2/ext3 filesystem 18 December 2007 extlinux(1)