03-25-2013
No, serial port 0 (or 1, whatever the lowest number is).
The A/B/C/D - just leave at default. That has particular meaning for IBM i (aka i5 or OS/400). It says which whether to boot from permanent or temporary firmware image.
Default is to boot from temporary. The concept is if a firmware change has unexpected issues you can IPL again on the permanent side (i.e. the old firmware).
At a certain point in time, the temporary side gets copied to permanent and they are the same. When the system comes up (AIX) run the command lsmcode. It will tell you what level both sides are at. (No clue what the C/D does. When I did a bit of OS/400 admin there was only an A/B side, so I am guessing C/D is just an extension of that.) - In short, leave that at the current (default) setting.
This User Gave Thanks to MichaelFelt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi
I need to access files from a specific folder of a Linux system from an another Linux System Remotely.
I know how to, Export a folder on One SCO System & can access the same by using Import via., NFS in the Sco Unix SVR4 System using the scoadmin utility.
Also, I know to use mount -t ... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
2. Solaris
Good morning,
I have a solaris 8 machine (Sunblade 1000) that is configured with NIS, I have checked everything I can think of to make sure everything is correctly configured which it appears it is but when I try to log into CDE it says it is unable to access my home area and it also does the... (1 Reply)
Discussion started by: Mr Pink
1 Replies
3. Solaris
Hi,
I have two Sun Fire V490 with Solaris 10 5/08, FC switch and two Sun StorageTek 3500 FC arrays. Each array is connected to switch and to one server at a time. In the last week I installed Solaris 10 5/08 on both servers and set up Sun Cluster, version 3.2. At wednesday all was fine - all... (7 Replies)
Discussion started by: Sapfeer
7 Replies
4. Shell Programming and Scripting
I am unable to access the value set inside the loop from outside loop .
Thought of taking this to forum , I had seen other replies also , where a pipe takes the execution to another shell and mentioned thats the reason we do not get the variable outside loop . But I am getting an issue and I am... (1 Reply)
Discussion started by: Armaan_S
1 Replies
5. Solaris
Hi,
I am refered to see Infodoc 80854. but I am not able to access from sun.com. Is there any precedure to view these?. Please guide me.
Thanks in advance. (1 Reply)
Discussion started by: bpsunadm
1 Replies
6. HP-UX
hi friends,
I am using hp unix HP-UX B.11.11 .. Generally i do the compression to maintain the space availability . To compress the files first i used the TAR to collect all the files. it has done fine. when i am using command ls in the folder which has TAR file , it shows the TAR... (2 Replies)
Discussion started by: rdhaprakasam
2 Replies
7. AIX
Hi,
I have tried to setup the console on a Power5 9131-52A type IBM Server. On the back there are 2 RS-232 ports labeled T1 T2. I am going under the assuming that these are the serial ports (Normally the serial ports are S1 S0). When I finish assigning the console under smit, I get no response... (3 Replies)
Discussion started by: mrmurdock
3 Replies
8. AIX
I have recently aquired the following machine:
IBM,9113-550
Up until yesterday we could connect a dumb terminal to serial port 1 and get console login. However the dumb terminal died. We are now using a laptop with a null modem cable attached to serial port 1. This works perfectly for all of... (1 Reply)
Discussion started by: rsw7724
1 Replies
9. Shell Programming and Scripting
Hi,
i have the following code in which i am passing array tldn in awk using -v option & despite of that condition is not getting matched,can somebody suggest how to handle shell arrays in awk
tcount=(9875 9667)
awk -F"\t" -v ltldn="${tldn}" 'NR==FNR {POSTPAIDMDNS=$2"|"$3;next}
... (6 Replies)
Discussion started by: siramitsharma
6 Replies
10. AIX
I am running AIX 7.1 and currently we have samba 3.6.25 installed on the server. As it stands some AIX folders are shared that can be accessed by certain Windows users.
The problem is that since Windows 10 the guest feature no longer works so users have to manually type in their Windows login/pwd... (14 Replies)
Discussion started by: linuxsnake
14 Replies
LEARN ABOUT XFREE86
ipwfw
IPWFW(4) BSD Kernel Interfaces Manual IPWFW(4)
NAME
ipwfw -- Firmware Module for Intel PRO/Wireless 2100 driver
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device ipwfw
This will include three firmware images inside the kernel. If you want to pick only the firmware image for the mode you want to operate your
network adapter in choose one of the following:
device ipwbssfw
device ipwibssfw
device ipwmonitorfw
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
ipw_bss_load="YES"
ipw_ibss_load="YES"
ipw_monitor_load="YES"
DESCRIPTION
This module provides access to firmware sets for the Intel PRO/Wireless 2100 series of IEEE 802.11 adapters. It may be statically linked
into the kernel, or loaded as a module.
For the loaded firmware to be enabled for use the license at /usr/share/doc/legal/intel_ipw/LICENSE must be agreed to by adding the following
line to loader.conf(5):
legal.intel_ipw.license_ack=1
FILES
/usr/share/doc/legal/intel_ipw/LICENSE ipwfw firmware license
SEE ALSO
ipw(4), firmware(9)
BSD
January 14, 2010 BSD