VET - that is to activate the Virtualization Features.
POD - to activate processors. I am not a hw guy, but as I understand it, A Model 9131-52a does not have dynamic activation of the processors. They are activated at the factory (or you would even be able to start, your supplier would not have been able to install, etc..)
You say you received/bought it - and it sounds like "pre-installed" with AIX 7.1.
I have a similar model the p5-51a (thinner and 2 processors, you can go to 4, and have more disks and/or perhaps you have a deskside.).
So, when the system is turned off - but plugged in (main unit is off, but ASMI web interface is working) - if the serial port is not responding at 19200 baud, either your cable is defective, or the serial port is defective.
After the firmware reset - the port will be active with power applied and the machine in "OFF" status.
FYI: I have VIOS installed in my initial partition - this is what gets started when I boot.
What is unclear to me is what you received. A stand-alone 9131-52a with AIX 7.1 as a single partition, or with VIOS installed (and sounds like no AIX).
I would ask your supplier to verify that the serial port functions (and also verify my serial cable is working - e.g., add a null modem just in case you have a straight cable atm). - Or ask your provider to supply/load a serial cable that they know works.
---------- Post updated at 01:44 PM ---------- Previous update was at 01:35 PM ----------
When I login via the serial cable - this is the dialog, and settings I have.
These were set by the installation.
From the command tty - you can see the firmware is managing the access (hence the name vty0, not tty0).
In short, we are really down to basics. Is the hardware working!?
The "other" way they can help is to provide an HMC for you to configure the system with (HMC creates a console connection via vty0 and the service processor. The is a GUI interface I dislike. When working with a HMC use (easier) the command vtmenu, otherwise the command mkvterm.
Hope this helps!
This User Gave Thanks to MichaelFelt For This Post:
Hi
I need to access files from a specific folder of a Linux system from an another Linux System Remotely.
I know how to, Export a folder on One SCO System & can access the same by using Import via., NFS in the Sco Unix SVR4 System using the scoadmin utility.
Also, I know to use mount -t ... (2 Replies)
Good morning,
I have a solaris 8 machine (Sunblade 1000) that is configured with NIS, I have checked everything I can think of to make sure everything is correctly configured which it appears it is but when I try to log into CDE it says it is unable to access my home area and it also does the... (1 Reply)
Hi,
I have two Sun Fire V490 with Solaris 10 5/08, FC switch and two Sun StorageTek 3500 FC arrays. Each array is connected to switch and to one server at a time. In the last week I installed Solaris 10 5/08 on both servers and set up Sun Cluster, version 3.2. At wednesday all was fine - all... (7 Replies)
I am unable to access the value set inside the loop from outside loop .
Thought of taking this to forum , I had seen other replies also , where a pipe takes the execution to another shell and mentioned thats the reason we do not get the variable outside loop . But I am getting an issue and I am... (1 Reply)
Hi,
I am refered to see Infodoc 80854. but I am not able to access from sun.com. Is there any precedure to view these?. Please guide me.
Thanks in advance. (1 Reply)
hi friends,
I am using hp unix HP-UX B.11.11 .. Generally i do the compression to maintain the space availability . To compress the files first i used the TAR to collect all the files. it has done fine. when i am using command ls in the folder which has TAR file , it shows the TAR... (2 Replies)
Hi,
I have tried to setup the console on a Power5 9131-52A type IBM Server. On the back there are 2 RS-232 ports labeled T1 T2. I am going under the assuming that these are the serial ports (Normally the serial ports are S1 S0). When I finish assigning the console under smit, I get no response... (3 Replies)
I have recently aquired the following machine:
IBM,9113-550
Up until yesterday we could connect a dumb terminal to serial port 1 and get console login. However the dumb terminal died. We are now using a laptop with a null modem cable attached to serial port 1. This works perfectly for all of... (1 Reply)
Hi,
i have the following code in which i am passing array tldn in awk using -v option & despite of that condition is not getting matched,can somebody suggest how to handle shell arrays in awk
tcount=(9875 9667)
awk -F"\t" -v ltldn="${tldn}" 'NR==FNR {POSTPAIDMDNS=$2"|"$3;next}
... (6 Replies)
I am running AIX 7.1 and currently we have samba 3.6.25 installed on the server. As it stands some AIX folders are shared that can be accessed by certain Windows users.
The problem is that since Windows 10 the guest feature no longer works so users have to manually type in their Windows login/pwd... (14 Replies)